manualshive.com logo in svg

Baroness LM2700, Service Manual

Share
Download
Baroness LM2700 Service Manual Download Page 250

Maintenance

Maintenance

This chapter describes primary checking and
maintenance operations for the LM2700 mower
unit.
For information on daily checks, maintenance
and handling of the machine, please refer to the
separate LM2700 Owner's Operating Manual
and Parts Catalogue.
For information on attaching and removing
optional parts and attachments, please refer to
the handling manual for the corresponding
attachment.

Specifications

Mower unit layout

#5

#1

#4

#2

#3

3crldz-002

Mower unit layout_001

Grease

Use the following type of grease on the
operating machine and mower units.

Grease

Excelite EP No. 2 (urea base)

LM2700

Operating Machine and Mower Units

Page 8-2

Maintenance

Summary of Contents for LM2700






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands