manualshive.com logo in svg

Baroness LM2700, Service Manual

Share
Download
Baroness LM2700 Service Manual Download Page 233

Installation of Subcover

Caution

See the list in "Tightening torques" (Page
3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

For installation, reverse the removing
procedure.

Removal of Left Tank Cover

Remove three bolts and anti-vibration
rubbers used to install the left tank cover,
and then remove the left tank cover.

2

2

1

1

2

3

dhlg83-002

Removal of Left Tank Cover_001

1

Bolt

2

Anti-vibration rubber

3

Left tank cover

Installation of Left Tank Cover

Caution

See "Tightening torques" (Page 3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

For installing it, reverse the removing
procedure.

1.

Removal of Right Tank Cover

Follow the steps below to remove the right
tank cover.

Remove the fuel tank cap.
Remove three bolts and anti-vibration
rubbers used to install the righttank
cover, and then remove the right tank
cover.

1

1

3

2

2

2

uk3xhk-002

Removal of Right Tank Cover_001

1

Bolt

2

Anti-vibration rubber

3

Right tank cover

Installation of Right Tank Cover

Caution

"Tightening torques" (Page 3-5) See .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening, etc.

For installation, reverse the removing
procedure.

1.

[1]
[2]

Main

 bo

dy

LM2700

Main body

Page 7-39

Removal and installation of each section

Summary of Contents for LM2700






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands