manualshive.com logo in svg

Baroness LM101, Owner'S Operating Manual, Page: 42 / 88

Share
Download
Baroness LM101 Owner'S Operating Manual Download Page 42

Operation Method

Cautions before Leaving The Machine

Caution

Park the machine on a flat place.
Do not park the machine on a slope.

Caution

Check that the engine has stopped.

Caution

Make sure that the brake lever is locked.

Positions of Operation Decals

7

4

5

2

1

3

6

8zq6pd-052

Positions of Operation Decals_001

1

Engine switch mark

2

Decal, light switch

3

Sticker, ON/OFF A (Unit clutch)

4

Sticker, ON/OFF A (Drum clutch)

5

Sticker, reel rotation

6

Decal, groomer indication

7

Decal, alignment 10300 (Set of 2pcs)

Description of Operation Decals

Engine Switch Mark

-
ENGINE SWITCH MARK
It illustrates the positions of the engine switch.

OFF

ON

rcyo1p-003

Engine Switch Mark_001

Light Switch Mark

Note:
Depending on the specifications, this function
may not be available.
K4203001610
DECAL, LIGHT SWITCH
It illustrates ON/OFF of the light.

1

2

mzmbmi-003

Light Switch Mark_001

1

ON

2

OFF

LM101

Handling Instructions

Page 4-20

Operation Method

Summary of Contents for LM101

























































































Reviews:

No comments