Baroness LM101 Owner'S Operating Manual Download Page 21

Page: 21 / 88

Description of Safety Decals and

Instruction Decals

Handling caution decal

K4205002150
DECAL, CAUTION HANDLING

㹉㸲㸰㸮㸳㸮㸮㸯㸳㸷㸮

mg5xtw-001

Handling caution decal_001

Use lead-free gasoline.

Warning

Read the Owner's Operating Manual.

Caution

Flying objects - Be sure that people around
the machine keep a safe distance away.

Warning

May cut your hand or leg - When the blades
are rotating, keep away from the machine.

1.
2.

PTO caution decal

K4205001760
DECAL, CAUTION PTO

Warning

May catch your arm - Keep away from PTO
moving parts during the engine running.

w267nz-002

PTO caution decal_001

Caution to Mutilation Decal

K4205001600
DECAL, CAUTION TO MUTILATION

Warning

May cut your hand or leg - Stop the cutter
rotation and engine. Otherwise you may get
injured.

STOP

wyikja-001

Caution to Mutilation Decal_001

Product Overview

LM101

Product Overview

Page 3-7

Safety Signs and Instruction Signs

Summary of Contents for LM101

























































































Search results

Summary of Contents for LM101

Reviews:

Baroness LM101, Owner'S Operating Manual, Page: 21 / 88

Search results

Summary of Contents for LM101

Reviews: