Baroness HMC156E Owner'S Operating Manual Download Page 10

-8-

2. Safety operation

Blades  rotate  at  high  speed  in  the  mowing  machine  under  severe  conditions  such 
as vibration, slope, and dust.  Operation conditions are subject to the place of use, 
existence of obstacles, condition of grass, etc. We sincerely desire that users should 
inspect  and  maintain  the  machine  completely,  make  efforts  to  master  the  machine 
operation skill, take measures for safety, use the machine correctly so as not to do 
harm to others, and give top priority to safety operation.

Wear  proper  clothes  that  will  not  be  caught  in  the 
machine,  and  wear  protective  gear,  goggles,  shoes, 
helmet, and gloves.
An  apron  and  a  towel  wound  around  the  waist,  as 
well as long strings especially, will cause the operator 
to  be  caught  in  or  pulled  into  the  machine,  which  is 
dangerous. Provide a fire extinguisher, first aid kit and 
secure  a  means  of  communication  to  deal  with  an 
emergency.

Clothes for safety

Avoid such operation

2-1.

Do not use the machine when you are tired. When you feel tired while using the 
machine, stop the work and take a rest.
Sick  people,  drunken  people,  and  people  under  the  influence  of  drugs  are 
not  allowed  to  use  the  machine. The  visual  sense,  nimbleness  in  action,  and 
judgment will be adversely affected.
When you are unfamiliar with machine operation, read the handling method and 
safety  precautions  to  understand  them  well  before  operating  the  machine.  Do 
not allow children to use the machine.

2-2.

Before  operating  the  machine,  check  the  field  by  necessity.  Pay  attention  to  the 
holes or obstacles.
Remove the objects that can fly apart as possible as you can. Give attention to the 
flying debris not to injure people, animals, crops, buildings, automobiles and so on.

Check the operating place.

2-3.

Do  not  operate  the  machine  with  mown  grass,  dust,  etc.  accumulated  in  the 
cover,  V-belt  or  around  the  engine  or  the  transmission,  otherwise  fire  or  other 
trouble may result. Remove them carefully. Improper maintenance and incorrect 
operation and dry grass  mowing might cause fire. Clean and check the machine 
as shown below before and during work.
Remove  dry  grass,  dust,  and  other  obstacles  from  around  the  muffler  and 
engine.
Check the fuel hose for cracks due to deterioration.
Check for fuel leakage during fuel supply.
Fuel supply during engine operation is prohibited.
Check the wiring to prevent fire due to a short circuit.
Inspect the fuel tank and carburetor for fuel leakage due to operation on a slope.
Be sure to carry a fire extinguisher and water etc. when mowing dry grass.
When cutting dried grasses, clean the machine every 1 hour.
In case of fire, use extinguisher to extinguish it in the early stage. When the fire 
expanded, evacuate to the safety place and report to the fire department.
Make sure of the expiry date of extinguisher at any time.

Prohibition of nighttime traveling and work

The  machine  is  not  provided  with  any  lighting  equipment.  Do  not  operate  the 
machine at nighttime or when the visibility is poor due to bad weather, etc.

2-5.

Do not remodel the machine. Use genuine parts for maintenance to ensure safety.

Remodeling of the machine prohibited

2-6.

Fire prevention

2-4.

CAUTION

WARNING

WARNING

C A U T I O N

C A U T I O N

Never use the machine for tree felling and wood chipping, tilling the farmland, or 
some  works  other  than  mowing,  otherwise  the  machine  may  lose  its  knife  shaft 
balance and cause failure.

Prohibition of work other than mowing

2-7.

C A U T I O N

WARNING

1

2

3

1

2

3

4

5

8

6

9

7

10

Summary of Contents for HMC156E









































Reviews: