page 36
page 36
page 36
page 36
page 36
275B SER
800-00152
HYDRAULIC COLLECTOR MAINTENANCE CONTINUED...
HYDRAULIC COLLECTOR MAINTENANCE CONTINUED...
HYDRAULIC COLLECTOR MAINTENANCE CONTINUED...
HYDRAULIC COLLECTOR MAINTENANCE CONTINUED...
HYDRAULIC COLLECTOR MAINTENANCE CONTINUED...
LOADED LIP SEAL
LOADED LIP SEAL
LOADED LIP SEAL
LOADED LIP SEAL
LOADED LIP SEAL
COLLECTOR SHOWN MAY NOT BE TYPE USED ON YOUR MACHINE BUT IS SHOWN AS A REFERENCE.
COLLECTOR SHOWN MAY NOT BE TYPE USED ON YOUR MACHINE BUT IS SHOWN AS A REFERENCE.
COLLECTOR SHOWN MAY NOT BE TYPE USED ON YOUR MACHINE BUT IS SHOWN AS A REFERENCE.
COLLECTOR SHOWN MAY NOT BE TYPE USED ON YOUR MACHINE BUT IS SHOWN AS A REFERENCE.
COLLECTOR SHOWN MAY NOT BE TYPE USED ON YOUR MACHINE BUT IS SHOWN AS A REFERENCE.
TOP OF
TOP OF
TOP OF
TOP OF
TOP OF
COLLECTOR
COLLECTOR
COLLECTOR
COLLECTOR
COLLECTOR
BEARING GUIDE RING
BEARING GUIDE RING
BEARING GUIDE RING
BEARING GUIDE RING
BEARING GUIDE RING
LOADED LIP
LOADED LIP
LOADED LIP
LOADED LIP
LOADED LIP
SEAL
SEAL
SEAL
SEAL
SEAL
SQUARE SEAL
SQUARE SEAL
SQUARE SEAL
SQUARE SEAL
SQUARE SEAL
BEARING GUIDE RING
BEARING GUIDE RING
BEARING GUIDE RING
BEARING GUIDE RING
BEARING GUIDE RING
O-RING
O-RING
O-RING
O-RING
O-RING
ASSEMBLY
ASSEMBLY
ASSEMBLY
ASSEMBLY
ASSEMBLY
1. All parts must be clean and free of oil and dust.
2. Install o-rings, loaded lip seals, or teflon rings on spool. See below for teflon rings:
TEFLON RING INSTALLATION:
NOTE:
NOTE:
NOTE:
NOTE:
NOTE: If any teflon rings are used, they must be heated in order to stretch them properly for installation.
Heat teflon rings to 200-400 degrees Fahrenheit.
WARNING
WARNING
WARNING
WARNING
WARNING
Do not heat teflon rings beyond 400 degrees Fahrenheit.
Do not heat teflon rings beyond 400 degrees Fahrenheit.
Do not heat teflon rings beyond 400 degrees Fahrenheit.
Do not heat teflon rings beyond 400 degrees Fahrenheit.
Do not heat teflon rings beyond 400 degrees Fahrenheit.
If teflon rings are heated beyond 400 degrees Fahrenheit
If teflon rings are heated beyond 400 degrees Fahrenheit
If teflon rings are heated beyond 400 degrees Fahrenheit
If teflon rings are heated beyond 400 degrees Fahrenheit
If teflon rings are heated beyond 400 degrees Fahrenheit
they will give off harmful toxic fumes.
they will give off harmful toxic fumes.
they will give off harmful toxic fumes.
they will give off harmful toxic fumes.
they will give off harmful toxic fumes.
When the right temperature is reached the teflon ring will act like a rubber band when shaken.
Using heat resistant gloves, grasp teflon ring and slip over end of spool to groove. Speed is essential before
contracting occurs.
Ensure ring is not twisted in groove.
NOTE:
NOTE:
NOTE:
NOTE:
NOTE: Rings that may be loose on spool may be sized by compressing with suitable hose clamp. Then
remove clamp before proceeding.
ASSEMBLY CONTINUED...
ASSEMBLY CONTINUED...
ASSEMBLY CONTINUED...
ASSEMBLY CONTINUED...
ASSEMBLY CONTINUED...
3. Install the two bearing guide rings at each end as shown.
4. Install the square seals on top of o-rings. Be careful not to over-stretch the seals.
5. Inspect for proper seal alignment and install spool in barrel using suitable assembly equipment.
6. Reinstall retaining plate and screws. Tighten screws.
7. Install safety wire on top end of collector.
