background image

Manual 2100-448E
Page

8 of 13

9. Connect leads with fork terminal to corresponding

points on unit terminal strip.  (See Manual 2100-
507 for air conditioner connection diagrams; see
Manual 2100-516 for heat pump connection
diagrams.)

10. Close control panel cover.

11. Replace left filter support, filter and four (4) screws

in condenser grille.

12. Reinstall the blower access panel at top of unit and

secure with sheet metal screws.

13. Ventilator Checkout

A. Remove mist eliminator to allow access to

minimum position thumbwheel or blade stops.

B. Resupply power to unit.

C. Energize the evaporator blower by switching

thermostat to the manual fan position with
heat/cool in OFF position.

D. Ventilator should open to the position set by

position adjustment thumbwheel on the CRVS,
or to the blade stops on the CRVP.  On the
CRVS, cycle position adjustment thumbwheel
to full open through full close.  Observe damper
blade operation throughout travel to assure free,
unobstructed movement.  (See Figure 5.)

E. De-energize evaporator blower.  Damper blade

should close.

G. This completes ventilator checkout.

14. Adjust damper blade for required ventilation

airflow.  (See next section.)

15. Replace mist eliminator.  Be sure it is installed with

the drain holes to the bottom.

16. Remove blank off plate or barometric fresh air

damper installed on service access door.  Plug four
(4) mounting holes with the plastic plugs provided
with the ventilator.

17. Replace service access panel.

18. Ventilator is now ready for operation.

Summary of Contents for CRVS-3














Reviews: