![background image](http://html.mh-extra.com/html/barco/xdl-4k30/xdl-4k30_user-manual_474399045.webp)
R5906151 /02
XDL
45
Status overview
Once the projector is started, press the
Menu Activation
button to get an overview of parameters such as :
•
Device serial number and article number
•
Current firmware version and model name
•
Current illumination (in percentage)
•
Projector runtime in hours
•
Uptime in hours
•
Chosen source
•
Current resolution and refresh rate
•
Chosen communication method and IP address (if connected)
•
Active functions
Starting image projection
1.
Make sure the available sources are connected to the appropriate input ports.
Tip:
If properly connected, the
“
SYNC
”
LED will light up ORANGE.
2.
Press the
Input Selection
button on the keypad or on the remote control until:
•
the LED of the selected source (the
“
SEL
”
LED) light up GREEN, and
•
the image of the selected source is projected.
1
2
Image 4-3
4.2 Switching to standby
About the switch off process
To switch off the projector in a safe manner to protect the internal electronics (avoid moisture due to warming
up) the temperature inside the sealed compartments has to be brought back to ambient in a controlled
manner. This process is called
deconditioning
.
How to switch to standby
1.
Press and hold the
Power on/off
button for 3 seconds on the local keypad, or press the
Power Off
button on
the remote control.
Caution:
Do not switch off the power from the projector until the laser status light is off. Also make sure
not to power off the chiller(s). The chiller(s) should remain on as long as the projector is powered on.
The projector goes to standby mode. The deconditioning cycle will start and the lasers will be turned off.
During this period the Power on/off button will blink. Once the deconditioning cycle has ended, the projector
will be in preconditioned state. If left alone, the projector will eventually go into standby mode. In both states,
the power on/off button will be lit WHITE.
Keep in mind that it can take up to 10 minutes to start the lasers again after they were switched off.
If there are only 30 to 45 minutes between the shows it
’
s advisable to keep the lasers on with
shutter closed. When the shutter is closed the lasers are automatically dimmed.
Summary of Contents for XDL-4K30
