Barco X8 Installation Manual Download Page 21

Page: 21 / 96

4. Components of a X8 Rental Tile

4. COMPONENTS OF A X8 RENTAL TILE

General introduction

The X8 rental tile has a rugged frame where X8 modules

t into to form one display tile. These modules are connected via a cable

string with theX8 Connection Box mounted inside the X8 rental frame. The X8 Connection Box has a HDMI input and output port to
connect the X8 rental tile with the neighboring tiles in the display.

Image 4-1
X8 Rental Tile

X8 Module.

X8 rental frame.

X8 Connection Box mounting bracket.

X8 Connection Box.

The following chapters describe and illustrate these three main components (X8 rental frame, X8 module and X8 Connection Box)
more in detail.

Overview

•

X8 Rental Frame

•

X8 Module

•

X8 Connection Box

R5905160 X8 RENTAL DISPLAY 25/02/2013

Summary of Contents for X8

































































































Search results

Summary of Contents for X8

Reviews:

Related manuals for X8

Brands by name

Popular brands

Barco X8, Installation Manual

Search results

Summary of Contents for X8

Reviews:

Related manuals for X8

Brands by name

Popular brands