background image

R5912118 /01

UST lens for F-series

12

2.1 When mounting the lens without the support

When using the safety cable

When mounting the lens in a projector without using the specially designed mounting support for this lens.

How to handle before mounting the lens.

1.

Stick 3 to 4 clips on the suface of the lens body (1).

2.

Snap the first loop end of the safety cable into one of the clips.

1

3

2

Image 2-1

3.

Slide the rest of the cable around the lens. Click the cable into every clip it passes in the loop.

4.

Slide the cable through the loop end at the beginning of the cable (2).

5.

Install an U-bolt on the lens holder with the open ends oriented outwards (3). Make sure that both a part of the
loop end and the outgoing part of the safety cable are placed in the enclosure.

6.

Close the U-bolt and tighten it.

Note:

Make sure the safety cable is tightened around the lens before tightening the U-bolt nuts.

7.

Place the shackle through the free loop end of the safety cable.

8.

Mount the lens in the projector.

9.

Secure the safety cable around the truss and secure the shackle by turning the safety ring of the shackle over
the open end.

2.2 Mounting the UST lens on a F90 projector

How to mount

1.

Turn the projector on its side or on its top cover.

2.

Place the bottom support plate on the bottom plate of the projector. Make sure that both fixation holes match
the holes in the bottom plate.

Mounting the lens

Summary of Contents for UST



























Reviews: