![background image](http://html1.mh-extra.com/html/barco/udm-series/udm-series_installation-manual_4258230013.webp)
13
R5911438 /08
UDM
•
Allowed ambient temperature range depends on altitude:
-
between 0 and 1000 meter altitude: ambient temperature range = 0°C (32°F) to 40°C (104°F)
-
between 1000 and 3000 meter altitude: ambient temperature range = 0°C (32°F) to 30°C (86°F)
•
Rated humidity = 0% RH to 80% RH Non-condensed.
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage potentials and risk of electric shock.
•
Refer all servicing to qualified service personnel.
•
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the
Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Malfunction unit
Remove all power from the projector and refer servicing to qualified service technicians under the following
conditions:
•
When the power cord or plug is damaged or frayed.
•
If liquid has been spilled into the equipment.
•
If the product has been exposed to rain or water.
•
If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
normal operation.
•
If the product has been dropped or the cabinet has been damaged.
•
If the product exhibits a distinct change in performance, indicating a need for service.
Stacking and transporting
•
Stack maximum 2 rental flight cases high. Never higher.
•
Surface on which flight case is standing must be level to ensure that the total load is evenly spread out
among the four wheels. The surface must also be able to support the load safely.
•
Before stacking or transporting flight cases, check the wheels and their fixation screws for wear or defects.
•
Before stacking or transporting flight cases, check that the four lock handles on each flight case are in
good working order and locked securely.
•
When stacked, make sure the wheels of the upper flight case are precisely positioned in the stacking
dishes of the flight case below.
•
Stacked flight cases may not be moved. Before stacking, the lower flight case must already be in its final
resting position before placing the second upon it.
•
Never stack loaded flight cases in a truck or other transport medium, unless each flight case is rigidly
strapped tight.
•
In the event of a wheel breaking, flight cases must be rigidly strapped tight to prevent a stack collapsing.
•
Use an appropriate forklift to raise flight cases and take the necessary precautions to avoid personnel
injury.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available
upon request via [email protected].
Summary of Contents for UDM Series
