![background image](http://html1.mh-extra.com/html/barco/slm-r12-plus/slm-r12-plus_service-manual_4253192115.webp)
15. Lamp Power Supply R7633705
Primary
Voltages
++15VM
•
used as feedback information for stabilization of all output voltages.
•
used in circuits with ”hot ground” on this board and via connector J603 on
the other board R7632103.
++24V
mainly used for supplying the two fans.
++15V
used on sheet 2/2 for several circuits, and also stabilized down to a stable
++5Vref.
Secondary
voltages
++110V
a floating voltage used to charge up the boostup capacitors (for the start up of
the lamp)
The SMPS starts up from 80Vac onwards. When the SMPS is in operation, the +380VM must drop first to 50V before the SMPS is
switched off. This accelerates the discharge of the electrolytic capacitors at the PFC output on the module R7632105.
15.5.5 Secondary circuit of the LPS.
Description
The separation / isolation between primary and secondary is realized with transformer T300. The relay RL2 , supplied from the line
TRAFO_RANGE, can change the ratio Nprim / Nsec from LOW to HIGH. The ratio changes from 22/3 to 17/3.
Inside the transformer, a temperature sensing NTC resistor T300 provides an increasing voltage with temperature at the
TEMP_TRAFO line.
This information is handled by the microprocessor and the projector is shut down when the transformer reaches a predefined over-
temperature value, a value stored in eeprom on the R7632105.
The reverse voltage across the rectifier diodes may be maximum 300V. The most critical is the switching off time of the diodes.
Heavy ringing at turning off the diodes should be avoided.
A snubber 100E/1nF clamps too high ringing voltages.
The 100A coils L300 and L301 filter the HF components of the rectified current.
The capacitors C308 in parallel with a capacitor of 3000µF (C309+C310) (when the relay contacts are closed) filter the DC lamp
voltage.
At starting up, the lamp voltage is boosted up by the boost circuit around Q363 up to 105V and this high lamp voltage switches on
Q364. The relay RL3 opens its contacts and puts hereby a 1 Ohm in series with the electrolytic capacitors. From the moment the
lamp starts, the capacitors discharge through this 1 Ohm. The lamp voltage drops and the relay goes in rest position, shortening
the resistors. The electrolytic capacitors are now in parallel on the lamp electrodes.
15.5.6 Measurement of the lamp voltage.
Description
The lamp voltage at the secondary side must be measured and sent to the controller IC on the module R7632103.
The I330 buffers the voltage from the divider R334, R335.
The output VS (Voltage Sense) is led out to the other board via pin 6 of the CONTROL connector J603.
The voltage division is such that we obtain a ratio of 10 or, VS = 0.1V for 1V on the lamp.
Because the controller module on the R7632103 only can handle voltages up to 5V,
the maximum lamp voltage that can be
measured is 50V
.
15.5.7 Lamp Current Measurement.
Description
The lamp current is relatively high and is a DC current.
A trace on the pcb (printed circuit board) board serves as current sense resistor (R340). The sensed voltage is amplified with I340
and I341, and the output voltage IS is adjusted with P340 to be equal at 0.04V for 1A in the output.
The NTC R346 compensates resistance variations in the pcb trace when the temperature varies.
The
maximum lamp current that can be measured is 125A.
R5976820 SLM R12+ PERFORMER 08/03/2005
113
Summary of Contents for SLM R12 Plus
