![background image](http://html1.mh-extra.com/html/barco/s3-series/s3-series_user-manual_3891629402.webp)
13. E2 Maintenance
13.28 Genlock Cable
Image 13-72
The
fl
at ribbon Genlock cable connects the Genlock Assembly to the System-Power board. This procedure
provides instructions on how to disconnect the cable on both sides.
Make sure the latches are fully engaged to prevent the cable from coming loose.
Concerned parts
R767269K
Cable Kit Set
Necessary tools
•
1 x Phillips Screwdriver #2
•
Hex Screwdriver
How to remove the Genlock cable
1. Remove the Genlock Assembly and disconnect the Genlock cable from the board. Follow the instructions as provided in the
previous section.
2. Turn the unit upside down and follow the steps detailed in other procedures to remove the Bottom Panel and the CPU module
from the System-Power board.
3. Remove the USB, VFD, 3RU and 1RU cables that are connected to the System-Power board.
4. Remove the screws that attach the System-Power Board to the standoffs.
5. Lift the System Power Board from the standoffs and
fl
ip it over, but don’t extend it too much.
6. Unplug the side of the Genlock cable that is plugged into the System Power board.
398
R5905948 EVENT MASTER DEVICES 17/07/2017
Summary of Contents for S3 series
