![background image](http://html1.mh-extra.com/html/barco/s3-series/s3-series_user-manual_3891629122.webp)
6. EM GUI orientation
6.15 Con
fi
guration Menu > Adjustment > Output Con
fi
guration
General
In the Output menu users can assign output connectors to con
fi
gurations and adjust signal parameters to match the display devices
connected to the unit.
Output Card arrangement
On the E2 model, the output cards occupy slots 11 through 13 and right justi
fi
ed to slot 13.
On the S3–4K model, the output cards occupy slots 7 through 8 and right justi
fi
ed to slot 8.
If there is an empty output slot, all output cards to the left of that empty slot will be red. Red indicates that although the cards will
operate properly, outputs from these cards will not be available at the Multiviewer.
Image 6-19
E.g. E2 with an empty output-card slot
If the card with the connectors that are part of an output con
fi
guration is missing, the card in the unit graphic and the output con
fi
g-
uration in the con
fi
guration list will be grayed out.
Also, if there is an existing output con
fi
guration but the card in the slot is of different type, then again the con
fi
guration will be greyed
out.
Output Connector Grouping
The connectors can also be grouped together to de
fi
ne a 3D* , 4K or Videowall con
fi
guration. For example, a projector that requires
2 DVI connectors to pass 3D Left and Right eye signals. Also 4 SDI connectors can be con
fi
gured as a 4K output in order to connect
to a 4K projector.
There are several rules that apply when de
fi
ning an output con
fi
guration:
1.
Each Output connector can only be assigned to one output con
fi
guration.
2.
Outputs in an output con
fi
guration must be of the same type AND in the same slot or in adjacent slots. For example, there
cannot be a HDMI connector and an SDI connector in the same output con
fi
guration.
3.
Max connectors for an output con
fi
guration = 4.
4.
Once output connectors are assigned to the same output con
fi
guration, all settings for the output connectors will be synchro-
nized.
5.
If an output connector is not assigned to an output con
fi
guration,
-
Output settings cannot be adjusted on that connector.
-
The connector cannot be assigned to a destination
Examples of 4K Valid Outputs:
118
R5905948 EVENT MASTER DEVICES 17/07/2017
Summary of Contents for S3 series
