![background image](http://html1.mh-extra.com/html/barco/prometheus-iii/prometheus-iii_installation-manual_4205234012.webp)
R5906897 /02
Prometheus III
12
Restriction zone
To protect untrained users and children against high intensity light beams, the light beam Hazard Distance
(HD) shall be taken into account.
1.3 Important safety instructions
To prevent the risk of electrical shock
•
This projector should be operated from an AC power source. Ensure that the mains voltage and capacity
matches the projector electrical ratings. If you are unable to install the AC requirements, contact your
electrician. Do not defeat the purpose of the grounding.
•
Installation according to the local electrical code and regulations by qualified technical personnel only.
•
This product is equipped with a barrier strip for the connection of a power line. The configuration is a three-
terminal barrier strip for the connection of a mono phase power line with a separate earth ground PE.
If you are unable to install the AC Requirements, contact your electrician. Do not defeat the purpose of the
grounding.
•
The cross-sectional area of the conductors in the power supply cord shall be not less than 4mm
2
(10
AWG).
•
The electronics of the projector must be powered either from a suitable UPS unit or from the power outlet
socket (UPS OUTLET) provided on the projector. For that reason an adapted short power cord (2-pole 3-
wire grounding) is added to the projector accessories to loop through the power.
•
The cross-sectional area of the UPS inlet cord shall be not less than 0.75 mm² or AWG 18.
•
The provided power output socket (UPS OUTLET) on the projector may only be used to provide power to
the projector electronics. Never connect other devices to this power output socket.
•
The circuit breaker(s) that must be provided in the power circuit(s) of the projector is considered as general
disconnect switch(es) to switch off the complete installation.
•
Disconnect the power to the projector mains terminals and unplug the power cord at UPS INLET for
removal of all power from the projector.
•
Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the
cord.
•
Do not operate the projector with a damaged cord or if the projector has been dropped or damaged - until it
has been examined and approved for operation by a qualified service technician.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should
be used. A cord rated for less amperage than the projector may overheat.
•
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous
voltage points or short circuit parts that could result in a risk of fire or electrical shock.
•
Do not expose this projector to rain or moisture.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified
service personnel before resuming operations.
•
Do not disassemble this projector, always take it to an authorized trained service person when service or
repair work is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect media and
communication cables. This will prevent damage to the projector due to lightning and AC power-line
surges.
To prevent personal injury
•
To prevent injury and physical damage, always read this manual and all labels on the system before
powering the projector or adjusting the projector.
•
Do not underestimate the weight of the projector. The projector by itself weighs ±147 kg ( ±324 lbs). To
prevent personal injury a hoisting tool should be used to lift the projector.
•
To prevent injury, ensure that the lens, cooling system and all cover plates are correctly installed. See
installation procedures.
Summary of Contents for Prometheus III
