![background image](http://html1.mh-extra.com/html/barco/prometheus-i/prometheus-i_safety-and-instruction-manual_4205255010.webp)
1. Safety
1.3
Important safety instructions
To prevent the risk of electrical shock
•
This projector should be operated from an AC power source. Ensure that the mains voltage and capacity matches the projector
electrical ratings. If you are unable to install the AC requirements, contact your electrician.
•
Installation according to the local electrical code and regulations by quali
fi
ed service personnel only.
•
This product is equipped with a barrier strip for the connection of a power line. The con
fi
guration depends on the projector:
-
Prometheus I: three-terminal barrier strip for the connection of a mono phase power line with a separate earth ground PE.
-
Prometheus II:
fi
ve-terminal barrier strip for the connection of a 3W+N+PE or 3W+PE power system.
If you are unable to install the AC Requirements, contact your electrician. Do not defeat the purpose of the grounding.
•
The cross-sectional area of the conductors in the power supply cord shall not be less than 4 mm
2
or AWG 10.
The cross-sectional area of the UPS inlet cord and external fan power cord shall be not less than 0.75 mm² or AWG 18.
•
The electronics of the projector (UPS INLET) must be powered either from a suitable UPS unit or from the power outlet socket
(UPS OUTLET) provided on the projector. An adapted short power cord (2-pole 3-wire grounding) is added to the projector
accessories to loop through the power from UPS OUTLET to UPS INLET.
•
The provided power output socket (UPS OUTLET) on the projector may only be used to provide power to the projector elec-
tronics. Never connect other devices to this power output socket.
•
The exhaust fan outlet may only be used to power an external blower, maximum 3A.
•
The building installation has to be provided with a circuit breaker of max. 40A to protect the complete unit.
•
A readily accessible disconnect device must be incorporated externally to the equipment for removal of the power to the pro-
jector mains terminals.
•
Disconnect the power to the projector mains terminals and unplug the power cord at UPS INLET for removal of all power from
the projector.
•
High leakage current. Earth connection essential before connecting supply.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
the cord, pull it out by the plug. Never pull the cord itself.
•
Do not operate the projector with a damaged cord. Replace the cord.
Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for
operation by quali
fi
ed service personnel.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of
fi
re or electrical shock.
•
Do not expose this projector to rain or moisture.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by quali
fi
ed service personnel before
resuming operations.
•
Do not disassemble this projector, always take it to quali
fi
ed service personnel when service or repair work is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, remove all power from the projector. This will prevent damage to the device due to lightning and AC power-line
surges.
6
R5905963 PROMETHEUS SERIES 09/03/2015
Summary of Contents for Prometheus I
