![background image](http://html1.mh-extra.com/html/barco/nw-12/nw-12_user-manual_3850258046.webp)
5. Setup
Once the projector is operational, the information strings are rotating in the same way as in the standby mode
(see Standby Status)
5.3
Setting up the RCU address
What has to be done ?
To allow the communication between the RCU and the projector the RCU has to be programmed with the same address as the
projector.
This address must be in the range 0-9.
To know the address of the projector, one can visualize it in projection mode (on screen) as well as in standby mode (shown with
the LED’s on top cover of the projector).
At this stage, the image projected may happen to be upside down or mirrored, this can be set in the
Installation
menu under
Projector orientation
(see further setting up the projector’s orientation).
Displaying the Projector Address in projection mode)
1. Press the
Address
key (recessed key on the RCU) with a pencil.
The projector’s address will be displayed on the screen in a Textbox
Programming the RCU
1. Push the address key If the address is not entered within 5 seconds, the RCU returns to its default address (zero address) and
controls then all projectors in the room.
2. Enter the same address with the digit buttons
within 5 seconds
after pushing the address key.
The projector can now be controlled with the RCU.
For example : if the projector address is 3, then press "3" on the RCU to set the RCU’s address to match the
projector’s address.
Common address/Projector address : Beside the projector address, the projector disposes also of a Common
address which can be set to “0” or “1” (by default “0”).
In other words, an RCU set to address “0” will always control a projector regardless of its projector address
(since it uses the common address).
5.4
Setting up the projector address (only if necessary)
What can be done ?
The projector is shipped with projector address set to ”0”
In some cases the projector address must be changed, for example if an unique RCU is used to control 2 or more projectors (inde-
pendently).
In the OSD menu
Projector Address
, the following addresses can be programmed :
•
Projector address: address de
fi
ned by the user, may be from 0 to 255
0-9 is used for RCU communication, 0–255 being used for RS232 serial communication.
•
Common address : address may be 0 or 1
How to change the projector’s address ?
1. Press
MENU
to activate the Tool bar
2. Press
→
to select the
Installation
42
R59770286 NW-12 25/09/2008
Summary of Contents for NW-12
