![background image](http://html1.mh-extra.com/html/barco/njord/njord_user-manual_4189179009.webp)
9
R5913592 /
Njord
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Notice on laser radiation
The laser distance meter that is optional equipment for this projector can emit a class 2 laser ranging beam of
0.95 mW / 638 nm. When installed correctly, this distance meter is located on the front side of the projector
(see ). The laser beam can be enabled by either pressing the button on the equipment, via the projector menu,
or via the projector software. Thermal retinal eye injury is possible when staring into the laser ranging beam.
Image 1
–
1
WARNING:
Laser Radiation
—
Do not stare into laser ranging beam, Class 2 IEC EN 60825-1:2014
See the product safety manual for details.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having
appropriate technical training and experience necessary to be knowledgeable of potential hazards to which
they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY
and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk
to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE
PERSONNEL, AUTHORIZED to operate professional projection systems.
The NJORD projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL
familiar with potential hazards associated with high voltage, high intensity light beams and high temperatures
generated by the light source and associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable
of such risks, are allowed to perform service functions inside the product enclosure.
1.2 Important safety instructions
To prevent risk of electrical shock
•
This product should be operated from a mono phase AC power source. Ensure that the mains voltage and
capacity matches the projector electrical ratings: 120-180V/200-240V (+/-10%), 16A-12A, 50-60Hz. If you
are unable to install the AC requirements, contact your electrician. Do not defeat the purpose of the
grounding.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable.
•
If none of the supplied power cables are the correct one, consult your dealer.
•
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the purpose of the grounding-type plug.
•
Never use 2- wire power cords, as this is dangerous and could lead to electrical shock. Always use a
power connector with a ground terminal.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the
cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
•
Use only the power cord supplied with your device. While appearing to be similar, other power cords have
not been safety tested at the factory and may not be used to power the device. For a replacement power
cord, contact your dealer.
•
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the purpose of the grounding-type plug.
•
Do not operate the projector with a damaged cord. Replace the cord.
•
Do not operate the projector if the projector has been dropped or damaged - until it has been examined
and approved for operation by qualified service personnel.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
Summary of Contents for Njord
