Barco HDX 4K User Manual Download Page 87

Page: 87 / 107

13. Servicing

How to install

1. Take the lamp house by its handles and gently slide the lamp house into its socket. Note that the compartment is provided with

a guide (1) to position the lamp house correctly.

Image 13-12
Insert lamp house

2. Push the lamp house forward until it slides fully into the projector.

Positioning pins (2) must match the holes (5) in the lamp house.

3. Secure this position by fastening the 3 spring lock screws.

4. Reinstall the lamp cover of the projector.

While starting up the projector, the electronics detect if a lamp is installed. If no lamp is installed, it is not
possible to start up the projector.

13.8 Replacement of the high density dust

lter

AUTION

The high density

lter must be replaced on a regular basis, depending on the environment condi-

tions of the projector.

R5906070 HDX 4K 23/09/2016

Summary of Contents for HDX 4K












































































































Search results

Summary of Contents for HDX 4K

Reviews:

Related manuals for HDX 4K

Brands by name

Popular brands

Barco HDX 4K, User Manual

Search results

Summary of Contents for HDX 4K

Reviews:

Related manuals for HDX 4K

Brands by name

Popular brands