Barco HDX 4K User Manual Download Page 16 | Manualshive

Page: 16 / 107

background image

2. Installation preparations

Main Power requirements

The HDX operates from a nominal mono phase power net with a separate earth ground PE.

Power requirements : 110-130V/200-240 V, 15A, 50-60Hz

The power cord required to connect the projector with the power net is delivered with the projector.

Projector weight

Do not underestimate the weight of the HDX. The projector weights about ±50 kg (±111 lb.) without lens. Be sure that the pedestal
on which the projector has to be installed is capable of handling

fi

ve (5) times the complete load of the system.

2.2

Unpacking the projector

What has to be done ?

Upon delivery, the projector is packed in a carton box upon a wooden pallet and secured with banding and fastening clips. Fur-
thermore, to provide protection during transportation, the projector is surrounded with foam. Once the projector has arrived at the
installation site, it needs to be removed from the carton box and wooden pallet in a safe manner without damaging the projector.

After unpacking let the projector acclimatize to a room temperature higher then 10°C (50°F) and lower then
40°C (104°F). Neglecting this may result in a start up failure of the Light Processor Unit.

Necessary tools

cutter knife

How to unpack

1. Remove the banding around the carton box, by releasing the fastening clips as illustrated, and open the box.

Image 2-1
Opening box

2. Remove the small box on top of the projector. This box contains the accessories such as manuals, remote control, etc.

12

R5906070 HDX 4K 23/09/2016

«
...
14
15
16
17
18
...
»

Summary of Contents for HDX 4K












































































































Reviews:

No comments

Related manuals for HDX 4K

Brand: NEC Pages: 2

Brand: QVS Pages: 1

Brand: CyberPower Pages: 2

COMPACTVIEW CLAN X15-I

Brand: 3D Perception Pages: 36

Brand: PLUS Vision Pages: 2

Brand: SVS Pages: 16

Brand: Ask Proxima Pages: 1

Brand: NEC Pages: 8

Innovate CP-AW100N

Brand: Hitachi Pages: 202

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 6

PT-FW300U - LCD Proj Wxga 600:1 3500 Lumens Enet 13.7LBS H/v Lens

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 1

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 14

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands