![background image](http://html1.mh-extra.com/html/barco/hdf-w-series/hdf-w-series_service-manual_474148321.webp)
19. Board Diagnostic LED’s
19.6 Communication Interface board Diagnostic LEDs
Location of the diagnostic LEDs
3
4
5
6
7
8
9
10
1
2
Image 19-8
1
++5V OK (green)
2
++3.3V OK (green)
3
ETH ACT (green/red)
4
10/100 (green/red)
5
PWR (green/orange/red)
6
ERROR (orange/red)
7
LMP (green/orange/red)
8
IR (green/red)
9
WIFI SEL (green/red)
10
ACT (green/red)
View on the diagnostic LEDs
The Communication Interface board is located inside the Input & Communication unit. Only the LEDs at the front side (cover plate)
are visible without opening the projector. To view the other diagnostic LEDs the Input & Communication unit has to be placed in the
service position as illustrated below (moved forward and tilted). The other LEDs are then visible through the grid at the sides of the
Input & Communication unit.
C
AUTION
:
Only operate the projector for a few minutes while the Input & Communication unit is moved and
tilted in it’s service position. This to minimize the risk of exceeding the maximum permitted internal temper-
ature limit due to insuf
fi
cient air
fl
ow.
Description of the diagnostic LEDs
Ref. Description (LED
color)
Comment
1
++5V OK (green)
This LED lit up in normal condition and indicates that the ++5V standby voltage from the PMP is
available. The ++5V is generated on the PMP and derived from the ++12V from the Power Box.
2
++3.3V OK (green)
This LED lit up in normal condition and indicates that the ++3.3V standby voltage from the PMP is
available. The ++3.3V is generated on the PMP and derived from the ++12V from the Power Box.
3
ETH ACT (orange)
This LED lit up in case the projector detects an Ethernet connection.
4
10/100 (red)
This LED lit up in case the projector detects an 100MB network.
5
PWR (green/or-
ange/red)
This three color LED indicates the
fl
owing:
•
OFF: the projector is switched off or is starting up.
•
RED: the projector is put in STANDBY.
•
ORANGE: the projector is put in ECO STANDBY.
•
GREEN: the projector is OPERATIONAL.
R5905312 HDF W SERIES 24/01/2013
317
Summary of Contents for HDF W series
