![background image](http://html1.mh-extra.com/html/barco/hdf-w-series/hdf-w-series_service-manual_474148139.webp)
8. Lamp and lamp house
8.7
Realignment of the lamp in its re
fl
ector
Each xenon lamp installation requires a realignment of the lamp in its re
fl
ector for optimal performance of the
xenon lamp in the projector. Furthermore, it is recommended to realign the Z-axis of the lamp after the
fi
rst
run time of 100 and 200 hours.
This procedure assumes that the lamp house with xenon lamp is already installed in the projector and that the
lamp house is equipped with thumbscrews for XYZ-aligment. Use a 2 mm Allen key in case no thumbscrews
are installed.
W
ARNING
:
This procedure may only be performed by quali
fi
ed technical service personnel.
Necessary tools
Light meter
How to align
1. Remove the cover of the lamp compartment to gain access to the X-, Y-, and Z-axis adjustment screws of the lamp.
2. Place a light meter in the center of the projection screen.
3. Loosen the locking screws x, y and z.
4. Switch on the projector and start up the lamp.
5. Adjust the X-axis, the Y-axis and the Z-axis for maximum light output. Carefully turn the thumbscrew for maximum light output.
Once over the maximum, turn slightly in opposite direction to reach the maximum light output again.
Do this for each direction and repeat this adjustment cycle twice.
X
Y
Z
y
x
z
Image 8-31
Lamp alignment
6. Turn the lock nuts against the plate to secure the current position.
7. Switch off the projector and reinstall the cover of the lamp compartment.
R5905312 HDF W SERIES 24/01/2013
135
Summary of Contents for HDF W series
