![background image](http://html1.mh-extra.com/html/barco/freya/freya_user-manual_4137593036.webp)
R5910032 /00
Freya
36
3.1 ICMP-X configuration via Web Communicator
About ICMP-X configuration
Following parameters are available to configure the ICMP-X:
•
Global settings: allows defining name of the ICMP-X, host name (network identifier) and IP address which
can be used for communication with external content devices.
•
User settings: definition of all users allowed on the ICMP-X.
•
Server settings: definition of access to servers and storage libraries of content (movies, KDM, etc.).
•
Player settings: Audio delay and audio output frequency.
•
Audio channel: allows defining the mapping of audio channels (content) on each audio output (AES
outputs of the ICMP-X.).
•
Scheduler setting: Enable/Disable scheduler at startup, delays allowed in scheduler mode and length of
schedule history.
•
Devices: allows defining communication ports settings, to access external devices controlled by the
automation.
•
Automation Cues: event cues that are triggered from different sources and to which can be assigned
actions to be executed by the automation engine.
•
Verify internal clock of the ICMP-X.
All installation and maintenance operations on the ICMP-X are performed via Web Communicator,
the Barco configuration software. Please refer to the user guide for further information.
About Default settings
The restore of factory setting is a feature that allows removing all settings performed on the ICMP-X and
replaces them with the default values set at the factory. Please refer to the Communicator user guide for
further information.
About the ICMP-X internal clock
The crystal on the ICMP-X board that manages the clock shows a certain drift (all crystals do). With the
Communicator the internal clock can be adjusted. This maintenance action should be repeated every 3
months. When neglected the system will locks up.
It is possible to enable NTP (Network Time Protocol). You have to configure (at installation) an IP address
where the ICMP-X can find a sync signal. From then on, and as long as the connection is active, the ICMP-X
will automatically keep its clock correct. For detailed instructions see user guide.
3.2 ICMP-X status LEDs
ICMP-X status LEDs and Reset button
LEDs on ICMP-X front panel give information on the status of the device.
1
2
Image 3
–
2
Summary of Contents for Freya
