![background image](http://html1.mh-extra.com/html/barco/f90-w13/f90-w13_user-manual_4126017010.webp)
1. Safety
•
Do not block the projector cooling fans or free air movement around the projector. Minimum safety distance to the exhaust area
of the unit must not be less than 100 cm (40”) and to the intake area, not less than 50 cm (20”).
•
Do not use this equipment near water.
•
Do not operate the projector outside its temperature and humidity speci
fi
cations as this may result in overheating and malfunc-
tion.
•
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices™ in which
case there is a loss of warranty.
•
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
•
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet.
Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
•
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-re
fl
ective
coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials
and risk of electric shock.
•
Refer all servicing to Barco authorized repair centers.
•
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can
lead to permanent damage to the projector and cancellation of the warranty.
•
Unplug this product from the wall outlet and refer servicing to Barco authorized service personnel or technicians under the
following conditions:
-
If liquid has been spilled into the equipment.
-
If the product has been exposed to rain or water.
-
If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a quali
fi
ed technician to restore the product to normal operation.
-
If the product has been dropped or the cabinet has been damaged.
-
If the product exhibits a distinct change in performance, indicating a need for service.
-
When the power cord or plug is damaged or frayed.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replace-
ment parts. Unauthorized substitutions may result in degraded performance and reliability,
fi
re, electric shock or other hazards.
Unauthorized substitutions may void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
1.3
Remote control warning
General
Laser radiation class II product, wavelength 670 nm; maximum output 1 mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11
Remote control complies with applicable requirements of EN / IEC 60825–1/2007.
Image 1-1
6
601–0400–00 F90–W13 18/08/2016
Summary of Contents for F90-W13
