background image

2. Getting to know the projector.

Broadcast address

Projector will always execute the command coming from a RCU programmed with that broadcast address.

2.10.1 Controlling the projector

Why a projector address?

As more than one projector can be installed in a room, each projector should be separately addressable with an RCU or computer.
Therefore each projector has its own address.

Set up an individual Projector Address

The set up of a projector address can be done via the software.

Projector controlling

Every projector requires an individual address between 0 and 255.

When the address is set, the projector can be controlled now:

with the RCU: only for addresses between 0 and 31.

with a computer: for any address between 0 and 255.

Broadcast Address

Every projector has a broadcast (common) address ’0’ or ’1’. The default address is ’0’.

The choice between ’0’ and ’1’ can be selected in the GUI: “

System Settings

Communication

“IR Control

“.

Placing new batteries in the remote control or plugging the remote to a projector via XLR cable will automati-
cally reset the address back to its default value ’0’.

2.10.2 Displaying and Programming addresses into the RCU

Displaying the Projector Address on the Screen.

1. Press the

Address

button to see the projector address (proximately 2 seconds).

The projector’s address is displayed on the LCD status screen.

How to Program an Address into the RCU?

1. Press the

Address

button until the

Button pressed indicator

lights up continuously (proximately 5 seconds).

2. Enter the address with the digit buttons within the time the indicator lights up (also proximately 5 seconds).

Note:

That address can be any value between 0 and 31.

Tip:

A few examples:

To enter address 3, press "3" digit button on the RCU to set the RCU’s address to 3 and wait until the button pressed
indicator is out. Alternatively, you can also press “0” and “3”. This way, he button pressed indicator goes out immediately.

To enter address 31, then press “3” and “1” on the digit button on the RCU and the button pressed indicator goes out
immediately.

2.11 Connector panel

General

The source input panel is located at the back of the projector. For source speci

fi

cations, see table below.

Image 2-8

601–426 F70 SERIES 16/06/2017

23

Summary of Contents for F70-W8











































































Reviews: