![background image](http://html1.mh-extra.com/html/barco/f70-series/f70-series_service-manual_3943371012.webp)
723
–
0018 /02
F70
12
2.1 General Safety Instructions
General Safety Instructions.
•
The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. For Northern America, the
projector is class 3R laser product up to throw ratio 2.33. The projector conforms with IEC 60825
–
1:2007,
and with performance standards for laser products under 21 CFR 1040, except with respect to those
characteristics authorized by Variance Number 2016
–
V-0144 effective March 6, 2017
•
This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk
Group 3 (RG3) when an interchangeable lens with throw ratio greater than 3.15 is installed. For Northern
America, installation requirements according to Risk group 3 (RG3) must be followed when
interchangeable lens with throw ratio greater than 2.33 is installed. Refer to the manual for the lens list and
throw ratio before operation. Such combination of projector and lens are intended for professional use only,
and are not intended for consumer use.
•
For RG3, no direct exposure to the beam shall be permitted. For RG3, operators shall control access to the
beam within the hazard distance or install the product at a height that will prevent eye exposure within the
hazard distance.
•
This projector has a built-in Class 4 laser cluster. Disassembly or modification is very dangerous and
should never be attempted.
•
Any operation or adjustment not specifically instructed by the user
’
s guide creates the risk of hazardous
laser radiation exposure.
•
Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.
•
Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
•
Not following the prescribed control, adjustment or operation procedure may cause damage by the
exposure of laser radiation.
•
Before operating this equipment please read this manual thoroughly and retain it for future reference.
•
Installation and preliminary adjustments should be performed by properly trained and qualified personnel.
•
All warnings on the projector and in the documentation manuals should be adhered to.
•
All instructions for operating and use of this equipment must be followed precisely.
•
All local installation codes should be adhered to.
2.2 Notice on safety
Safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1,
as basis for National safety regulation world wide. The safety standard covers information technology
equipment including electrical business equipment intended to operate in
“
normal
”
environments (offices and
homes). This safety standard imposes important requirements on the use of safety critical components,
materials and insulation, in order to protect the user or operator against risk of electric shock and energy
hazard and having access to live parts. Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection
against the risk of fire. Simulated single fault condition testing reduce the risk of hazards and contribute to
ensure the safety of the equipment to the user even when the equipment
’
s normal operation fails..
2.3 Users Definition
Definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having
appropriate technical training and experience necessary to be knowledgeable of potential hazards to which
they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY
and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk
to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks,
are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers
to any person other than SERVICE PERSONNEL. When an interchangeable lens with throw ratio above a
certain level is installed, the F70 / 90 series projector becomes RG3. Refer to the manual for the lens list and
hazard distance before operation. Such combination of projector and lens are intended for professional use
only, and are not intended for consumer use.
Summary of Contents for F70 Series
