![background image](http://html1.mh-extra.com/html/barco/f70-4k6/f70-4k6_user-manual_474063065.webp)
601
–
426-03
F70 Series
65
5.4.3 Going from READY to ON
Description
Press the
Power On/Off
button on the projector, or the
Power On
button on the remote control. The projector
will power
ON
. The
Power On/Off
button will BLINK BLUE during the transition from
READY
to
ON
. Once the
projector is on, the
Power On/Off
button will be lit BLUE.
5.4.4 Going from ON to READY
Description
Press and hold the
Power on/off
button on the projector for 3 seconds, or press the
Power Off
button on the
remote control. The projector will power down through a cool down phase. The
Power on/off
button will BLINK
WHITE during the transition from
ON
to
READY
. Once the projector is in
READY
, the
Power on/off
button will
be lit WHITE.
5.4.5 Going from READY to ECO standby
Description
If ECO Standby mode is enabled in the service menu (refer to the section "GUI - system settings/Standby
ECO", in User Guide) the projector will automatically go to
ECO
standby mode after a time-out (default 15
minutes). All electronics (including fans, pumps,...) go down except for a very small wake up controller. The
Power on/off
button will FLASH WHITE every second.
5.4.6 Going from ECO to ON
Description
Press the
Power on/off
button on the projector, or the
Power On
button on the remote control. The projector
goes from
ECO
directly to
ON
. The projector will go through the same booting phase as on power plugging,
then do the transition from
READY
to
ON
. Of course startup-time will be longer then from
READY
to
ON
.
5.4.7 Wake On LAN (WOL)
About
The projector has WOL functionality, that can be used for the projector to go from ECO mode to READY
mode. Use a json command for transition from READY to ON.
The WOL is performed by sending a Magic Packet followed by the projectors MAC address. The MAC
address is found in the menu
Home / System settings / Communication / LAN.
The MAC address is similar to
the HW address that is shown in this menu path.
5.5 Power modes
General
The table below details the F70 power modes.
Mode
Description
Normal
Projector is booted up and the light source is on
Ready
Projector is booted up but the light source is off
ECO Standby
Light source is switched off and projector electronics
are powered down
Summary of Contents for F70 - 4K6
