System Setup
Ethernet Port
Connect to Ethernet Switch on an isolated
network. Used for communications with
devices such as Video Processors, video
routers, matrix switchers, ScreenPRO-II,
PresentationPRO-II and ImagePRO. Also
used for downloading code.
Quick Start Guide
Visibly yours
Barco Media and Entertainment
11101 Trade Center Drive
Rancho Cordova, CA
95670 • USA
Phone:
Fax:
Technical Support:
Website:
+1 (916) 859-2500
+1 (916) 859-2515
+1 (866) 374-7878
www.barco.com
P/N 26-0313003-00, Rev A
ID Setup and Remote Enable
— Set up individual
Video Processor, ScreenPRO-II, PrePRO-II and
ImagePRO IDs. Enable remote control on all units.
Before you begin, ensure that your system is properly
cabled. Use the sample “configuration” charts in
Chapter 3 of the User’s Guide.
AC
Connect to AC
power source
1
Peripheral Power Up, Status Check
— Power up
routers and peripherals. Use
Status Menu
to check
code compatibility. Download code (if required).
2
Return to Factory Default
— Perform a complete
factory reset on all devices. This procedure resets all
router tables and source mappings.
3
Touch Screen Calibration
— Calibrate the
Controller’s Touch Screen display(s).
4
Restore from Flash Memory Card
— If you backed
up to Flash Memory, restore the configuration at this
point. No further setup steps are necessary.
5
Programming EDID
— For your background and DSK
sources, program EDID to ensure proper
communications to your PCs at the preferred resolution.
6
Destination Setup
— Set up single screen, wide
screen, stack and ScreenPRO-II destinations. Note that
“stacking” is only available with the Controller LC.
7
Router Setup
— Set up your system’s routing
switcher(s), including type, communications, output
patching, and designating Aux outputs.
8
Aux Destination Setup
— Set up your system’s
Auxiliary destinations, including Aux, ImagePRO Aux
and PresentationPRO-II Aux destinations as required.
9
Input Patching
— Associate (patch) specific router
inputs to specific source buttons on the Controller.
Assign tally connections as desired.
10
Output Format Setup
— Configure the output format
for each Video Processor and ScreenPRO-II. Always
match the native resolution of the display or projector.
11
Genlock Setup
— Set up Genlock for each destination
selected on the
Output Menu
.
12
Sync Setup
— Set up sync parameters for the monitors
and projectors connected to the system.
13
Projector Setup
— Set up your projectors for both
single screen and wide screen destinations.
14
Background Setup
— Set up the Controller’s two
background sources for all single, wide screen, stack
and ScreenPRO-II destinations.
15
Input Setup
— Set up your system’s inputs for single,
wide screen, stack and ScreenPRO-II destinations.
Both “quick” and “detailed” methods are outlined.
16
DSK Setup
— Set up the Controller’s DSK source.
Choose between “none,” DVI, analog or a captured
frame grab.
17
18
Save the Setup
— On the
System Keypad
, press
SAVE
to save the state of the Controller in non-volatile
memory.
19
Backup to Flash Memory Card
— Back up your
system configuration to a customer-supplied Flash
Memory Card.
20
System setup is comprised of 20 sequences,
each of which includes many steps. For
error-free installation, always refer to the
associated section in Chapter 6 of the User’s Guide.
The circled sequence numbers are identical.
ETHERNET
CONSOLE
TALLY
KEYBOARD
USB B
MultiMedia Card
EXT COMM
100-240 V
47-63Hz, 2.75A
Keyboard Port
Connect to customer-supplied PS/2
keyboard. Enables certain numeric
entry and “naming” functions.
USB Port
Not Used
MultiMedia Card
Insert customer-supplied
Flash Memory Card (min.
512 MB). Enables storage,
recall and transfer of
system configurations.
Ext Comm Port
For serial
communications
with external devices
such as routers
Console Port
For serial
communications and
downloading code
Tally Connector
Connect to 8 external devices for
relay closure control. Refer to
Appendix A for connector pinouts.
D/A Setup
— Set up your system’s Distribution
Amplifiers, including type, number of outputs, and
output patching.
Encore Controller — Rear Panel: Models SC and LC
Note
: Use MMC or MMCPlus cards.
Do not use SD cards.