![background image](http://html1.mh-extra.com/html/barco/dp2k-slp-series/dp2k-slp-series_user-and-installation-manual_474005094.webp)
9. Starting up
9.1
Switching the DP2K SLP-series ON
How to switch on?
1. Ensure that the DP2K SLP-series is installed onto a stable platform.
2. Ensure the projector is correctly connected to the mains power.
3. Ensure that the correct lens is installed for your application.
4. Check if a video source is connected to the projector.
5. Press the
Power Switch
to switch the projector
ON
. As a result the projector starts up and the communicator touch panel starts
its initialization procedure.
Note:
The projector always boots up in the same mode (E.g. Standby or Sleep) as it was switched off. This procedure assumes
that the projector was switched off in standby mode (projector fully operational but light source is off).
6. Wait until the status light of the projector lights up
GREEN
(not
fl
ashing).
7. Press the
STANDBY
button on the Local Keypad or use the Communicator to activate the light source.
8. Press the
DOWSER
button on the Local Keypad or use the Communicator to open the dowser.
DOWSER
Image 9-1
How to awake the projector from Sleep mode?
1. Press the
SLEEP
button on the Local Keypad for three seconds or use the Communicator to put the projector in Standby mode.
As a result the projector starts booting and initializing all electronics. During the booting and initializing phase the backlight color
of the Sleep button is purple (transition phase). Once the projector is fully awake the backlight color of the Sleep button is green.
Note:
When the projector is in Sleep mode only the backlight of the Sleep button lights up red. The backlight of all other buttons
of the Local Keypad remains off.
The backlight color of the Sleep button, Standby button, Dowser button and Test Pattern button must all light
up green to project the image of the applied source.
C
AUTION
:
See user’s guide of the Communicator Touch Panel to operate and control the DP2K SLP-series.
When for any reason a restart of the projector is required, the content server should be restarted also.
90
R5906847 DP2K SLP SERIES 02/06/2017
Summary of Contents for DP2K SLP Series
