Barco DP2K SLP Series User And Installation Manual Download Page 29

Page: 29 / 175

3. Installation process

3.2

Software upgrade

How to upgrade the software

1. Switch on the projector. The projector can now be switched on. Place the

ON/OFF

switch of the projector in the ”I” position. As a

result the projector starts to initialize. The status lights of the projector lights up GREEN once the projector is initialized. In case
the status lights up RED may indicate a tamper event during transport. If so, contact Barco customer service.

2. Download and install the latest version of Communicator. The program can be downloaded for free from Barco’s website, (URL:

http://www.barco.com

). Click on

myBarco

and login to get access to secured information. Registration is necessary.

If you are not yet registered, click on

New to myBarco

and follow the instructions. With the created login and password, it is

possible to login where you can download the software.

3. Download the latest

rmware from Barco’s website in the same way as for Communicator.

4. Start Communicator and make a connection with the projector. For more information, consult the Communicator user guide.

5. Login as service technician and click on tab

Maintenance

and select

Software update

6. Click on

Launch DC update companion

7. Click

Next

, accept the license agreement and continue following the wizard.

R5906847 DP2K SLP SERIES 02/06/2017

Summary of Contents for DP2K SLP Series
















































































































































































Search results

Summary of Contents for DP2K SLP Series

Reviews:

Related manuals for DP2K SLP Series

Brands by name

Popular brands

Barco DP2K SLP Series, User And Installation Manual

Search results

Summary of Contents for DP2K SLP Series

Reviews:

Related manuals for DP2K SLP Series

Brands by name

Popular brands