![background image](http://html1.mh-extra.com/html/barco/dp2k-slp-series/dp2k-slp-series_service-manual_474006350.webp)
R5906848 /04
DP2K SLP Series
350
Code 20135:
“
LCB
–
Turn-on PFC LDM 1
–
6 failed
”
Situation
Solution
Cable or conn36 V
shorted.
Check / reseat the cable between LDM 1
–
6 and LCB connector J601.
Def36 V module
Replace the +36V module in the LDM (LDM slot 6). See service procedure
Replacing a Laser Drive Module
”
, page 56.
Defective LCB
Replace the Laser Control Board (LCB). See service procedure
”
, page 64.
Code 20136:
“
LCB
–
Turn-on PFC LDM 1
–
7 failed
”
Situation
Solution
PFC (+380 VM / VMA) could
not be switched on during the
startup process of the
projector.
Replace the +24 V module in the LDM (LDM slot 1
–
7). See procedure
Replacing a Laser Drive Module
”
, page 56.
Code 20137:
“
LCB
–
LDM power configuration mismatch
”
Situation
Solution
Difference in firmware version.
Upgrade the software to the latest version. See procedure
“
update via Communicator (DC update companion)
”
The LDM did not switch on or
not all power parts are
detected.
Check if the +36 V and +24 V modules are in their correct slot (1
–
6 and 1
–
7 respectively). Correct their positions if necessary. See procedure
Replacing a Laser Drive Module
”
, page 56.
See
Bad wiring connection
Check / reseat the cables between the LDM2 and the LCB.
Code 20142:
“
LCM 1
–
Fan 1 speed too low
”
Situation
Solution
Fan speed too low due to
wiring issue.
Check/reseat the wire connections on the fan interconnection board.
Fan speed too low due to fan
damage.
Remove the Light Source from the projector and do the following:
1.
Remove the fan from the Light Source assembly and check if this
numbered fan is not blocked.
2.
If not blocked, replace the fan.
For removing the Light Source, see service procedures in
, page 59. For removing and replacing the fan, see
procedure
Replacing a fan from the Light Source
, page 75.
Defective Cooler Control
Board.
1.
Replace the Light Source Fan Interconnection board. See procedure
“
Replacing the Light Source Fan Interconnection Board
, page 72.
2.
If problem persists, replace the entire Light Source. See procedure
“
, page 59.
Code 20146:
“
LCM 1
–
Fan 2 speed too low
”
For this error the same troubleshooting table can be applied to as for code
20142
:
“
LCM1
–
Fan 1 speed too
low
”
.
Summary of Contents for DP2K SLP Series
