![background image](http://html1.mh-extra.com/html/barco/dp2k-slp-series/dp2k-slp-series_service-manual_474006349.webp)
R5906848 /04
DP2K SLP Series
349
Code 20103:
“
LLS
–
Bank 3 is off
”
For this error the same troubleshooting table can be applied to as for code
20101
:
“
LLS
–
Bank 1 is off
”
.
Code 20104:
“
LLS
–
Bank 4 is off
”
For this error the same troubleshooting table can be applied to as for code
20101
:
“
LLS
–
Bank 1 is off
”
.
Code 20105:
“
LLS
–
Bank 5 is off
”
For this error the same troubleshooting table can be applied to as for code
20101
:
“
LLS
–
Bank 1 is off
”
.
Code 20106:
“
LLS
–
Bank 6 is off
”
For this error the same troubleshooting table can be applied to as for code
20101
:
“
LLS
–
Bank 1 is off
”
.
Code 20107:
“
LLS
–
Bank 7 is off
”
For this error the same troubleshooting table can be applied to as for code
20101
:
“
LLS
–
Bank 1 is off
”
.
Code 20108:
“
LLS
–
Bank 8 is off
”
For this error the same troubleshooting table can be applied to as for code
20101
:
“
LLS
–
Bank 1 is off
”
.
Code 20109:
“
LLS
–
Bank 9 is off
”
For this error the same troubleshooting table can be applied to as for code
20101
:
“
LLS
–
Bank 1 is off
”
.
Code 20128:
“
LCB
–
FCB forces lasers off at start-up
”
For this error the same troubleshooting table can be applied to as for code
20070
:
“
LCB
–
FCB forces lasers
off
”
.
Code 20129:
“
LLS
–
Phosphor wheel motor speed too low at start-up
”
For this error the same troubleshooting table can be applied to as for code
20046
:
“
LCB
–
Phosphor wheel
motor speed too low
”
.
Code 20131:
“
LCB
–
Turn-on LCM 1 failed
”
Situation
Solution
Light Source cooling could not
be switched on during startup
sequence
•
Check / reseat the communication cable between the LCB (J600) and
the light source fan interconnection board (J101).
•
Upgrade the software to the latest version. See procedure
“
update via Communicator (DC update companion)
•
If problem persists, replace the fan interconnection board. See service
procedure
“
Replacing the Light Source Fan Interconnection Board
,
Code 20133:
“
LCB
–
Turn-on PFC LDM 1 failed
”
Situation
Solution
PFC (+380 VM / VMA) could
not be switched on during the
startup process of the
projector.
•
Check / reseat the power connection to the LDM.
•
If problem persists, replace the LDM. See service procedure
“
Replacing a Laser Drive Module
, page 56.
Summary of Contents for DP2K SLP Series
