![background image](http://html1.mh-extra.com/html/barco/dp2k-slp-series/dp2k-slp-series_service-manual_474006026.webp)
R5906848 /04
DP2K SLP Series
26
3.1 1 month maintenance actions
MAINTENANCE TYPE A (perform every month)
The 1 month maintenance actions, listed below, may be performed by a trained projectionist who is
familiar with potential hazards associated with the product.
No.
Maintenance action
Remarks
1
Check
both dust
filters
of the projector for
dust
and
grease
.
Grease on the filter can build up after several months in an
environment contaminated with greasy air. Note that areas where
popcorn is consumed are subject to greasy air.
•
If the filters are contaminated with
dust
than cleaning the filters
with a
vacuum cleaner
should be sufficient.
•
In case the filters feel
greasy
than the filters must be
washed
.
Take into account that the time needed to dry the dust filters may
be 24 hours or more. For that, it's recommended to have a second
set of dust filters which can be used while cleaning the first set.
Replace damaged filters
immediately.
See procedures
“
”
, page 284, and
“
”
,
page 285.
To speed-up drying, allow the
filter(s) to dry at 50°C max in a
well ventilated room.
2
Check the surface of the lens output side for dust. (it is not needed
to remove the lens from the projector). Only clean if necessary.
Clean the lens output side in
case dust is clearly visible upon
the surface.
Note:
if the lens was removed
from the projector, a manual
“
Lens Home & Return
”
action
must be executed to calibrate
the position of the lens in
relation to the Lens Holder. This
way the references of the
existing 'lens files' remain valid.
See user guide of the
Communicator software.
3
Check the porthole (both sides) for dust.
Clean the porthole in case dust
is clearly visible upon the
surface. Use an optical cloth.
3.2 3 month maintenance actions
MAINTENANCE TYPE B (perform every three months)
The 3 month maintenance actions, listed below, may be performed by a trained projectionist who is
familiar with potential hazards associated with the product.
No.
Maintenance action
Remarks
1
Clean the back/side air inlet vents of the Light Source.
Use a vacuum cleaner.
2
Clean the housing of your projector.
Removal overall dust
accumulation on projector
covers. See cleaning
instructions in this manual.
3
Verify the internal clock of the ICMP with real time clock. Correct if
needed.
ICMP version 1.2.1 is required.
Communicator version 5.0 is
required.
See user guide of
Communicator for detailed
instructions.
Summary of Contents for DP2K SLP Series
