Barco DP2K-E series User And Installation Manual Download

Page: 98 / 163

12. Convergence

12.2 Preparing for convergence adjustment

Necessary tools

•

7mm

at screwdriver.

•

3mm Allen wrench.

How to set up the projector for convergence adjustment?

1. Remove the top cover from of the projector.

2. Remove the left side cover from of the projector.

3. Remove the left cover plate of the Light Processor compartment.

4. Place the fan on top of the Light Processor in the upper position as illustrated. Do this by engaging the two lower slots (2) into

the upper mounting pins as illustrated. The two upper slots (3) remain free.

Image 12-3

5. Switch on the projector, ignite the lamp and open the dowser.

6. Select the convergence test pattern, which is illustrated below (image 12-4). Use the communicator to activate the convergence

test pattern.

Note:

The convergence test pattern can NOT be activated via the

PATTERN

button on the Local Keypad.

R5906693 DP2K-E SERIES 19/06/2015

Summary of Contents for DP2K-E series




































































































































































Search results

Summary of Contents for DP2K-E series

Reviews:

Related manuals for DP2K-E series

Brands by name

Popular brands

Barco DP2K-E series, User And Installation Manual

Search results

Summary of Contents for DP2K-E series

Reviews:

Related manuals for DP2K-E series

Brands by name

Popular brands