Barco DP-1200 Installation Manual Download Page 80

Page: 80 / 134

9. Projector registration

9.1

Introduction

Overview

The current projector is DCI compliant and should be registered by Barco. Therefore, the digital certi

cate inside the projector will

be used to secure encryption key communication between the projector and the rest of the theatre system (server and theatre man-
agement system). The

lm distributor will send keys to the theatre that are unique for the installed trusted digital cinema equipment

of that theatre. The

lm distributor will

nd its information about a theatre in the same database as where the projector is registered.

Barco plays as an intermediate station between the theatre and the

lm distributor.

Once a projector is registered, the uploaded data can be changed via the update procedure.

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands