Barco DP-1200 Installation Manual Download Page 53 | Manualshive

Page: 53 / 134

background image

5. Lenses & lens holder

5.4

Lens removal

How to remove a lens from the projector lens holder ?

1. Support the lens with one hand while you unlock the lens holder by sliding the lock handle towards the “unlocked” position as

illustrated.

Image 5-8

2. Gently pull the lens out of the lens holder.

Image 5-9

It’s recommended to place the lens caps of the original lens packaging, back on both sides of the removed
lens to protect the lens.

It’s recommended to place the foam rubber of the original projector packaging, back in the lens opening to
prevent intrusion of dust. Note that this foam rubber is packed in a plastic bag to prevent the dust, emitted by
the foam, from entering the projector.

R59770242 DP-1200 06/01/2009

49

«
...
51
52
53
54
55
...
»

Summary of Contents for DP-1200







































































































































Reviews:

No comments

Related manuals for DP-1200

Brand: VASTEX Pages: 7

Brand: RocketFish Pages: 2

Brand: Dukane Pages: 2

Brand: Barco Pages: 59

Brand: Enercell Pages: 14

X2 multi-use perfomance

Brand: InFocus Pages: 67

Brilliant LC-SB15

Brand: Eiki Pages: 1

Brand: Projectiondesign Pages: 86

Brand: Screen Technics Pages: 8

GAI-TRONICS 12576-120

Brand: Hubbell Pages: 2

TheaterLite DXG-210

Brand: Zenith Pages: 13

Brand: Optoma Pages: 1

Brand: Optoma Pages: 1

Brand: Eaton Pages: 12

Ritzscreen V540

Brand: Verano Pages: 12

Liebert Surge and Signal Protection

Brand: Emerson Pages: 4

Liebert Precision Cooling

Brand: Emerson Pages: 2

PowerSure 350-500VA

Brand: Emerson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands