Barco DP-1200 Installation Manual Download Page 25

Page: 25 / 134

3. Physical Installation

3.2

Installation of the exhaust system

About Exhaust

The exhaust stack of the projector head is designed to

t a 201 mm (7.91 inch) diameter duct. This size must be used throughout

the entire system and installed to eliminate any possibility of downdraft or rain dripping into the lamp house.

The exhaust blower must be capable of removing minimum 6,65 m

/min (235 CFM).

AUTION

If more than one projector is installed in a common projection booth, the above exhaust air

must be measured at EACH individual projector head exhaust stack. Inadequate exhaust draft can contribute
to premature xenon bulb lamp failure.

How to install the Exhaust stack

See illustration below:

Image 3-5

Ensure good condition of the lamp house blower. Keep the blower inlet clean for unrestricted air

ow.

To ensure maximum bulb life, operate the lamp house blower and the exhaust system for at least ten minutes
after extinguishing the bulb.

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands