Banner TCNM-AD Series Parameter Manual Download Page 52

Page: 52 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

Station Name

This parameter is meaningful and mandatory only for the Profinet interface. It is a string (max 240 characters) which

identifies the node on the network as an alternative to the IP address. If this value is changed by the host application

during runtime, a reset is required in order for changes to have effect.

The Name can be made up only of letters or numbers. The

(dot) and

(dash) characters can be used but not as the

first or last character in the Name.

Fieldbus

This option determines the communication between the scanner, or, in a multi-sided layout, between several scanners

and the selected Fieldbus network.

The following parameters allow enabling the communication through the TCNM-ABB5 Gateway to the Fieldbus

network.

Status

This parameter must be enabled for Serial-based Fieldbus modules: Profibus, DeviceNet, CANopen, and CC-Link.

For Ethernet-based Fieldbus modules (Ethernet/IP - TCP/IP, Profinet IO - TCP/IP, and Modbus TCP - TCP/IP) when

using TCP/IP communication only, performance can be improved by disabling the Fieldbus communication. In this way

more resources are freed up for TCP/IP communications.

Data Tx

If enabled (checked), data from the scanner will be transmitted on the Fieldbus network.

Heartbeat

This parameter enables/disables transmission of the Heartbeat message used to signal device or system status at

regular intervals. The Heartbeat message is independent from Data Tx and can be enabled even if data is not sent on

the Fieldbus network (Data Tx - disabled).
Selections:

Disable

the Heartbeat message is not transmitted

Enable Unconditioned

the Heartbeat message is always transmitted, even if
communication is still active

Enable Conditioned

the Heartbeat message is transmitted only when there is no
communication

Heartbeat

The following parameters allow enabling the communication through the selected Fieldbus interface protocol.

The Heartbeat message is used to signal the device's or system's status at regular intervals to the Host. It has the

following format:

Timeout

This parameter defines the amount of time between two message transmissions. If the selected time out expires and

no transmission has occurred, the Heartbeat message will be transmitted.

Heartbeat Header String

This parameter signals the beginning of the Heartbeat message. It can be a string of up to 128 characters.
Selections: characters from

NUL

(00H) to

(7EH)

The Heartbeat Header String should be different from the Heartbeat Terminator String.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands