Table 43: Certified Antennas for 900 MHz 1 Watt
Model Number
Antenna Type
Maximum Gain
Impedance
Minimum Required Cable/
Connector Loss
-
Integral Antenna
Unity gain
0
BWA-9O1-x
Omni, 1/4 wave dipole
≤2 dBi
50 Ω
0
BWA-9O2-C
Omni, 1/2 wave dipole, Swivel
≤2 dBi
50 Ω
0
BWA-9O6-A
Omni Wideband, Fiberglass Radome
≤8.2 dBi
50 Ω
2.2 dB
BWA-9O5-B
Omni Base Whip
≤7.2 dBi
50 Ω
1.2 dB
BWA-9Y10-A
Yagi
≤10 dBi
50 Ω
4 dB
13.7 FCC and ISED Certification, 2.4GHz
This equipment contains transmitter module DX80-2400 or SX243.
FCC ID:
UE300DX80-2400
IC: 7044A-DX8024
FCC ID: UE3SX243
IC: 7044A-SX243
HVIN: DX80G2 /
DX80N2 / SX243
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device contains licence-exempt transmitters(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil contient des émetteurs/récepteurs exemptés de licence conformes à la norme
Innovation, Sciences, et Développement économique Canada. L’exploitation est autorisée aux
deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, and (2) L’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
FCC Notices
IMPORTANT: The transmitter modules DX80-2400 and SX243 have been certified by the FCC / ISED for use with other
products without any further certification (as per FCC section 2.1091). Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the equipment.
IMPORTANT: The transmitter modules DX80-2400 and SX243 have been certified for fixed base station and mobile
applications. If modules will be used for portable applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID/IC label must be visible through a window on the final device or
it must be visible when an access panel, door, or cover is easily removed. If not, a second label must be placed on the
outside of the final device that contains the following text:
Contains Transmitter Module [DX80-2400 or SX243]
FCC ID: [UE300DX80-2400 or UE3SX243]
IC: [7044A-DX8024 or 7044A-SX243]
HVIN: [DX80G2, DX80N2 or SX243]
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna,
•
Increase the separation between the equipment and receiving module,
Sure Cross
®
DXM100-Bx and DXM1000-Bx Wireless Controllers
www.bannerengineering.com - Tel: + 1 888 373 6767
107
