background image

PICO-AMP Miniature Remote Sensing System

PICO-AMP

Miniature Remote Sensing System

MD14 Modulated Amplifer and Ultra-small Remote Sensors

*NOTE: 9 m (30') cables are available by adding suffix “W/30” to the model number

of the cabled sensor (e.g., MD14BB6 W/30)

PICO-AMP MD14 Amplifier Models

PICO-AMP Features

Ultra-small remote sensors to fit the tightest locations

Three fixed frequency selections or Auto Frequency mode to prevent crosstalk in
multiple-sensor applications

Amplifier clips to 35 mm DIN rail for easy mounting

Diffuse- or opposed-mode sensors are available

Opposed-mode sensors are sold in pairs

Opposed-mode range is 300 mm; diffuse-mode range is 50 mm

Amplifiers and sensors are sold separately

Yellow indicator on emitter signals when light is sensed; Yellow indicator on
amplifier signals light sensed and flashes to indicate marginal excess gain
(between 1.0 and 1.5x)

An excellent option for wafer handling applications, small parts sensing and
pharmaceuticals applications

MD14BB6

MD14BB6Q

Models

Sensor

Compatibility

Cable

Supply

Voltage

SP3ER1
SP3ER2
SP8ER1
SP8ER2
SP3D1

2 m (6.5')

4-pin Pico-style QD

10-30V dc

Output Type

Bipolar,
NPN/PNP

WARNING . . .

Not a Safety Device

These remote sensors and component amplifiers do NOT include the self-checking redundant circuitry necessary to allow
their use in personnel safety applications. A sensor or amplifier failure or malfunction can result in either an energized or a 
de-energized amplifier output condition.

Never use these products as sensing devices for personnel protection. Their use as a safety device may create an unsafe condition which
could lead to serious injury or death.

Only MICRO-SCREEN

, MINI-SCREEN

®

, MULTI-SCREEN

®

, MACHINE-GUARD

and PERIMETER-GUARD

Systems, and other systems so

designated, are designed to meet OSHA and ANSI machine safety standards for point-of-operation guarding devices. No other Banner
sensors or controls are designed to meet these standards, and they must NOT be used as sensing devices for personnel protection.

!

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for PICO-AMP MD14BB6









Reviews: