Banner MINI-ARRAY BASIC Instruction Manual Download Page 3

1 Product Description

MINI-ARRAY BASIC Two-Piece Measuring Light Curtain configured for material handling and logistics applications with auto-

stream serial output, two discrete outputs, and EIA-485 communication

Simple two-piece measuring light curtain for profiling and object detection, tailored for material handling and logistics

applications

Diagnostic LEDs provide a simple means of monitoring emitter and receiver conditions and diminished performance

from dirty lenses

Models available with array lengths from 150 mm (6 in) to 1210 mm (4.7 ft) in 150 mm (6 in) increments

Beam spacing 19.1 mm (0.75 in) and a maximum range of 2 meters

Two discrete outputs plus auto-stream EIA-485 serial communication that automatically streams data without a

command

Configurable via the EIA-485 serial interface and the Banner Sensors GUI software within 5 seconds after the power

supply starts

Alarm output signals dirty lens and system fault conditions

EIA-485 serial communication enables a computer to process scan data

WARNING:

Do not use this device for personnel protection

Using this device for personnel protection could result in serious injury or death.

This device does not include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A device failure or malfunction can cause either an energized (on)
or de-energized (off) output condition.

1.1 Models

Emitter Model

Receiver Model

Array Length (Y)

Overall Length

Total

Beams

Sensor Scan Time (ms)

Interlaced

Scan

Straight

Scan

1

MBE616Q Emitter

MBR616PX485SQ

143 mm (5.62 in)

251 mm (9.9 in)

8

1.4

0.9

MBE1216Q Emitter

MBR1216PX485SQ

295 mm (11.62 in)

403 mm (15.9 in)

16

2.5

1.5

MBE1816Q Emitter

MBR1816PX485SQ

448 mm (17.62 in)

555 mm (21.9 in)

24

3.6

2.0

MBE2416Q Emitter

MBR2416PX485SQ

600 mm (23.62 in)

708 mm (27.9 in)

32

4.8

2.6

MBE3016Q Emitter

MBR3016PX485SQ

752 mm (29.62 in)

860 mm (33.9 in)

40

5.9

3.2

MBE3616Q Emitter

MBR3616PX485SQ

905 mm (35.62 in)

1013 mm (39.9 in)

48

7.0

3.7

MBE4216Q Emitter

MBR4216PX485SQ

1057 mm (41.62 in)

1165 mm (45.9 in)

56

8.1

4.3

MBE4816Q Emitter

MBR4816PX485SQ

1210 mm (47.62 in)

1318 mm (51.9 in)

64

9.2

4.8

The receiver's two discrete outputs are set to PNP by default, but can also be configured to NPN.

1 Worst-case response time is twice the scan time.

 

 

MINI-ARRAY

®

 BASIC Two-Piece Measuring Light Curtain

 

www.bannerengineering.com - Tel: + 1 888 373 6767

3

Summary of Contents for MINI-ARRAY BASIC

















Reviews: