Banner EZ-SCREEN SLSP14-450Q88, Instruction Manual, Page: 43 / 59

8 Specifications and Accessories
An EZ-SCREEN Type 2 System includes a compatible emitter and receiver (equal length; available separately or in pairs), and two cables.
Mounting hardware is included with each emitter and receiver. Interfacing solutions include IM-T-.. modules, or redundant positively
guided contactors; see Interface Modules on page 48.
8.1 Specifications
8.1.1 General Specifications
Short Circuit Protection
All inputs and outputs are protected from short circuits to +24 V dc or dc
common
Electrical Safety Class
III (per IEC 61140: 1997)
Safety Rating
Type 2 per IEC 61496-1, -2
Category 2 PL c per EN ISO13849-1
8 Beams 96 Beams
MTTFd (EN ISO 13849-1) 284.14 yr. 47.65 yr.
Mission Time, Tm 20 years
Operating Range
0.2 to 15 m (8 in. to 50 ft) — Range decreases with use of mirrors and/or lens
shields:
• Lens shields — approx 10% less range per shield
• Glass-surface mirrors — approx 8% less range per mirror
See the specific mirror datasheet for more information.
Resolution
30 mm
Effective Aperture Angle (EAA)
Meets Type 2 requirements per IEC 61496-2, Section 5.2.9 ±5° at 3 m
Ambient Light Immunity
> 10,000 lux at 5° angle of incidence
Strobe Light Immunity
Immune as per IEC 61496-2
Response Time
Dependent on number of beams (see EZ-SCREEN Type 2 Models With Response
Times on page 12)
Enclosure
Extruded aluminum housing with yellow polyester powder finish standard and
well-sealed, rugged die-cast zinc end caps, acrylic lens cover
Environmental Rating
IEC IP65
Operating Conditions
0 °C to +55 °C (+32 °F to +131 °F)
95% maximum relative humidity (non-condensing)
Shock and Vibration
Components have passed vibration and shock tests according to IEC 61496-1.
This includes vibration (10 cycles) of 10-55 Hz at 0.35 mm (0.014 in) single
amplitude (0.70 mm peak-to-peak) and shock of 10 g for 16 milliseconds (6,000
cycles).
Certifications
8.1.2 Emitter Specifications
Supply Voltage at the Device
24 V dc ±20% (use a PELV-rated power supply according to EN IEC 60950). The
external voltage supply must be capable of buffering brief mains interruptions
of 20 ms, as specified in IEC/EN 60204-1.
Supply Current
50 mA maximum
Wavelength of Emitter Elements
Infrared LEDs, 850 nm at peak emission
8.1.3 Receiver Specifications
Supply Voltage at the Device
24 V dc ±15% (use a PELV-rated power supply according to EN IEC 60950).The
external voltage supply must be capable of buffering brief mains interruptions of
20 ms, as specified in IEC/EN 60204-1.
Supply Current (no load)
90 mA maximum, exclusive of OSSD1 and OSSD2 loads (up to an additional 0.5 A
each)
EDM Input
Power monitoring accomplished via Reset/Remote Test input
Reset Input/Remote Test Input
Connect to +24 V dc via a normally closed (N.C.) reset switch
Auto Reset (Trip Output) Models: Test/Reset
Manual Reset (Latch Output) Models: Test/Restart/Reset
Output Signal Switching Devices (OSSDs)
Two redundant solid-state 24 V dc, 0.5 A max. sourcing OSSD (Output Signal
Switching Device) safety outputs. (Use optional interface modules for ac or
larger dc loads.) Not capable of the Banner "Safety Handshake".
ON-State voltage: ≥ Vin-1.5 V dc
OFF-State voltage: 0 V dc typical, 0.5 V dc maximum (no load)
Maximum load capacitance: 100 nF
Maximum cable resistance to load: 5 ohms per wire
Open ground leakage current: 0.65 mA maximum
OSSD test pulse width: 200 to 250 microseconds typical
OSSD test pulse period: 260 ms typical
Status Indicators
See Status Indicators on page 35 and Emitter Reset on page 38
Emitter: Green LED, Power ON
Receiver: Two yellow alignment indicators (top and bottom), two status
indicators (blocked and clear)
8.1.4 Emitter and Receiver Dimensions
EZ-SCREEN
®
Type 2 Light Screen
www.bannerengineering.com - Tel: 763.544.3164 43