Banner DXM1200-X2, Instruction Manual

Page: 41 / 83

February 02, 2024
DXM1200-X2 Controller Instruction Manual
© Banner Engineering Corp. All rights reserved.
41
Activate a Worldwide 4G LTE MNB-IOT Cellular Plan (RED-CE)
The Worldwide 4G LTE-M/NB-IOT cellular modem is operational in those European countries that are members of the EU/
EEA and adopt RED/CE-compliant products.
An international roaming SIM is provided with the Worldwide module and may be activated following the steps listed in
"Activate a 4G LTE CAT M1 Cellular Plan" on page 40 . However, there may be regions that are not covered by the provided
SIM card. In this case, a local SIM card must be activated and operated with this device to acquire connectivity services.
Configure the DXM Controller for a Cellular Modem
Use the DXM Configuration Software to create a configuration using a cellular connection.
IMPORTANT: Only the DXM100 and DXM150 models in conjunction with an SXI-LTE-001 (obsolete)
cellular modem can offer SMS/text messaging capabilities directly from the device. Contact a support
specialist at Banner Engineering for configuration instructions, or SMS/text messaging can be delivered
using the Banner CDS web service from any DXM model.
Select the cellular subscription plan. Please use the calculator and regional coverage information to determine
the plan needed for your device (
https://www.bannerengineering.com/us/en/products/wireless-sensor-
networks/iot-cloud-cellular-data-services/cellular-data-plans/Service-Plan-Calculator.html ).
b.
Create a username and password (use an email address for the username). c.
Enter your payment information, mailing address, agree to the terms and conditions. d.
Go to the My Services and Equipment section. 4.
Enter the SIM Number (ICCID) and the Module Number (IMEI).
The ICCID is the 20-digit number of the SIM, the bottom barcode number on the SIM card carrier. If the carrier card is
not available, the ICCID is also printed on the SIM card, but must be removed from its socket to be read. The IMEI is
the 15-digit number on top of the 4G LTE device.
5.
Click Activate.
Enter the ICCID and IMEI numbers then click Activate
Although new activations are typically functional in 20 minutes or less, it may take up to 24 hours for the cellular plan
to become active on the wireless network.
6.
Work with the local Banner technical support person to identify and purchase machine-to-machine (M2M) (data plan
only) SIM cards in 3FF 'micro' form factor.
Typical monthly data use will be 20-50 MB per month. When choosing a plan, pay close attention to data rates.
1.
When activating the SIM, note the Access Point Name (APN) that the SIM provider states to use with their SIM.
The IMEI is the 15-digit number on top of the cell module PCB, below the words Telit ME910G1-WW and above the
barcode. The ICCID is the 20-digit number printed on the SIM card itself.
2.
Go to the Settings › Cloud Services screen. 1.
Set the Push Interface to Cell
All push data will be sent using the cellular modem.
2.
◦
◦
Go to the Settings › Cellular screen. Under the Cell Configuration section, select the Cell module from the drop-down
list.
For the United States (contiguous) —For Verizon LTE/CATM modems, select SXI-LTE-001 or SXI-
CATM1VZW-001 and set the APN to vzwinternet.
For North America
—For ATT LTE/CATM modems, select SXI-CATM1ATT-001 and set the APN to
iot0119.com.attz. Requires a SIM module to be purchased from a wireless carrier based on the IMEI number
of the cellular modem. The wireless carrier will provide the APN parameters. Not all parameters may be
required.
3.