Banner DF-G2 High Speed Expert Instruction Manual Download Page 11

Page: 11 / 31

Remote

Input

5x
6x

7x
8x

10 µs (High-Speed)
15 µs (Standard)
50 µs (Long Range)
250 µs (Standard Speed)
500 µs (Medium Range)
1000 µs (Long Range)
2000 µs

2 Pt. TEACH
Dynamic TEACH
Window SET
Light SET
Dark SET
CAL SET

Min. Offset
2% *
5%
10%
20%
50%

Button Unlock (uloc)
Button Lock (loc)

Numeric
Percent

Numeric Flipped
Percent Flipped

ECO Numeric
ECO Percent

ECO Numeric Flipped
ECO Percent Flipped

PRO Basic

PRO Advanced

(continued at top)

(continued from below)

Button Lock (loc) or Unlock (uloc)

Factory Default Settings

5x
6x

Auto Thresholds ON
Auto Thresholds OFF

0 ms
2 ms
5 ms
10 ms
20 ms
50 ms

5x
6x

0 ms
2 ms
5 ms
10 ms
20 ms
50 ms

5x
6x

Auto Gain
Gain 1
Gain 2
Gain 3
Gain 4
Gain 5

8x
9x

Gain 6
Gain 7
Gain 8

Two Point TEACH

2Pt tch, then 1234 2nd

PASS or FAIL (with % Minimum Diff.)

Dynamic TEACH

dYn tch, then 1234 dYn

PASS or FAIL (with % Minimum Diff.)

Light SET

Lt SEt then PASS or FAIL*

Dark SET

dr SEt then PASS or FAIL*

Window SET

wind SEt then PASS or FAIL*

Calibration SET

CAL SET then PASS or FAIL

TEACH

METHODS

PROGRAM (Basic)

PROGRAM (Advanced)

* with % offset if not hard fail

Response Speed

TEACH Selection

Offset Percent

Button Lock

Display Readout

Auto Thresholds

Off Delay

Off One-Shot

On Delay

On One-Shot

Gain Select

0.04 seconds < T < 0.8 seconds
Timing between Pulse groups > 1 second

Pulse Timing (T)

NOTE: Follow procedure for the selected TEACH/SET method
(highlighted in black box) chosen in the TEACH Selection menu

In Super High-Speed and High-Speed Responses, 2% offset is forced to Min. Offset

5x
6x
7x

(Long Range with
immunity to energy-
efficient lights)

Figure 4. Remote Input Flowchart

DF-G2 High Speed Expert

™

Dual Display Fiber Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Summary of Contents for DF-G2 High Speed Expert































Search results

Summary of Contents for DF-G2 High Speed Expert

Reviews:

Banner DF-G2 High Speed Expert, Instruction Manual, Page: 11 / 31

Search results

Summary of Contents for DF-G2 High Speed Expert

Reviews: