manualshive.com logo in svg

Banner DF-G1 Expert, Manual

Share
Download
Banner DF-G1 Expert Manual Download Page 27

For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com

Accessories

SA-DIN-CLAMP

• Pair of metal DIN rail end stops; slide onto DIN rail at ei-

ther side of DF-G1 sensor stack

• Combination (#2 Phillips, #8 standard slotted) set screw

 

9.1 mm 
(0.36")

9.1 mm 

(0.63")

45.0 mm 

(1.77")

 

SA-DIN-BRACKET

• 1 plastic bracket with mounting screws

 

 

SA-DIN-BRACKET-10

• Package of 10 plastic brackets with mounting screws

DIN-35-..

• 35 mm DIN Rail
• Model

Length

DIN-35-70

70 mm

DIN-35-105

105 mm

DIN-35-140

140 mm

 

 

Banner Engineering Corp Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of
shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned
to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse,
abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (IN-
CLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND
WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL
BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPEN-
SES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY
PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WAR-
RANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or
liabilities relating to any product previously manufactured by Banner Engineering Corp.

 

 

DF-G1 - Expert Dual Display Fiber Amplifier Manual

 

 

 

Summary of Contents for DF-G1 Expert




























Reviews:

No comments

Brands by name

Popular brands

Load more brands