manualshive.com logo in svg

B&R Industries SDL4, User Manual

Share
Download
B&R Industries SDL4 User Manual Download Page 24

System overview 

24

SDL4 Converter User's manual V 2.00 Translation of the original documentation

3.6.2.1.6 LED status indicators

5COSD4.1000-00

5COSD4.1001-00

Converter - LED status indicators

LED

Color

Status

Explanation

LED status indicator

On

Device ready for operation

Green

Blinking

(approx. 1

Hz)

Device ready for operation, but an invalid or

incomplete firmware upgrade is indicated.

Information:

The firmware upgrade must be per-

formed again.

Status

Red

On

Firmware upgrade is in progress.

On

The SDL and SDL4 connection is established

and OK.

Off

No active SDL and SDL4 connection.

Blinking

(approx. 1

Hz)

No active SDL and SDL4 connection, but link

partner found.

Information:

In DVI mode, this LED blinks to indi-

cate limited SDL4 operation.

5COSD4.1000-00

•

SDL4 Out

5COSD4.1001-00

•

SDL4 Out 0

•

SDL4 Out 1

•

SDL4 Out 2

Yellow

Blinking

(approx. 10

Hz)

Firmware upgrade is in progress.

Summary of Contents for SDL4



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands