Doc #: 161038_00 Part #:72975
KPX-7V2
Wir
eless Keypad
1.1 Coding KPX into the Opener
The Opener can only operate from keypads that have been programmed into
its receiver. The receiver needs to learn the codes of any keypad / transmitter
that will be used by the operator.
a. Decide which Channel button (eg. 1 = Garage Door) is to be used to
operate your garage door.
b. To code the Channel button to the operator’s receiver press and release
the Code Set button on the Opener, then select your Channel button and
hold for 2 seconds.
c. Release the Channel button and pause for 2 seconds.
d. Select the same Channel button and hold for 2 seconds.
e. Release both the Channel button and the Code Set button.
NOTE:
If more than one device is to be controlled (for example: garage door
and sliding gate) then repeat this step for each Channel button to be used
(record the channel function in the table on the back page of this instruction).
Legend:
0 - 9
Pin Code Keys
1 - 8
Channel Numbers (CH#)
CLR
Clear Button
FCN
Function button for pr
ogramming
Doorbell contr
ol
Pr
oceed to
Quick Set up Guide
User Information T
able
Memory
(MEM)
User Name / Infor
mation
Channel (CH#) Allocation
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Channel Function
CH#
Receiver / Function
1
2
3
4
5
6
7
8
0
1. Quick Set up Guide
Safety Rules
•
Install
the
Wir
eless
Keypad
in
a
location wher
e the garage door
is visible, but out of r
each of
childr
en, at a height of at least
1.5m.
•
W
atch the moving door
and
keep people away until the
door is completely opened or
closed.
Do not operate door
when persons ar
e near the door
.
•
Do not allow childr
en to
play with door contr
ols or
transmitters.
There are 8 Channel buttons (keypad no. 1 - 8) in the KPX-7 to store functions and these can be programmed for example
(1 = Garage Door, 2 = Automatic Gate, 3 = Outside light)
If only a single User Pin and one channel function (Garage Door) is required, proceed to the Quick Set Up Guide.
Alternatively for multiple User Pins and / or mulitple receivers, follow the Quick Set Up Guide and then proceed to
Sections 2 and 3.
Getting Started
1.2 Program Primary User
Select a PIN code (4 - 8 digits) to be used to operate the keypad and save it
using the following steps (or below Short cut Guide):
a. Press and hold the FCN button. The Keypad will beep and flash to indicate
it is in learning mode. Release button.
b. Enter in your new 4 digit User Pin Code and press FCN button.
c. Re-enter the same 4 digit User Pin Code and press the FCN button.
d. The Keypad will beep and flash to indicate it is exiting learning mode.
WARNING! Record the Primary User PIN Code. If this PIN
Code is lost / forgotten the unit has to be sent back to the
factory to be reset
.
Short cut Guide - Program Primary User
Open out for more functions and features
BEEP
FCN
HOLD
USER 1 PIN
(4 - 8 digits)
FCN
FCN
FLASHES
USER 1 PIN
BEEP
FLASHES
W
rong Pin Code
If a wr
ong pin code is enter
ed,
a specific sound is hear
d after
pr
essing
the
function
(FCN)
key
. The
clear (CLR) key must be pr
essed to
start r
e-entering the pin code. On
the fourth consecutive wr
ong pin
code
entry
,
an
alarm
(light
blinks
and
sound
beeps)
is
trigger
ed
for
10 seconds. Every next wr
ong pin
code entry will trigger the alarm.
The time out for the wr
ong pin code
is one minute.
The Wir
eless Keypad has built-in
keypad lighting for use at night
or in dark ar
eas. The keypad will
illuminate upon pr
essing a button.
Built in lighting
1.3 Test the Operation of the Keypad
Test operation by entering the User Pin Code followed by selecting a
programmed Channel button.
NOTE:
Hold the selected Channel button until the channels function
activates.
NOTE:
by pressing another Channel button (and holding) within 10
seconds from releasing the first Channel button, will activate the
second Channel function (eg. 3 = Outside light) without having to
re-enter the User Pin Code.
1.4 Change User Pin
To change the User Pin, simply enter the User Pin, then follow step
1.2a - d.
Short cut Guide - Change User Pin
USER PIN
BEEP
FLASHES
NEW
PIN
FCN
NEW
PIN
FCN
BEEP
FLASHES
FCN
HOLD
