B&B Electronics Zlinx ZP Series Manual Download Page 9

Page: 9 / 49

Manual Documentation Number: ZPXXx-XXXXx-MR-0812

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 –

www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 –

www.bb-europe.com

LED Indicators

Note: In order for the RSSI LED to continuously indicate the signal strength, set the
RP command (RSSI PWM Timer) to FF.

Radio Frequency Information

The Zlinx Product is shipped with an antenna with the
following expected ranges.

These ranges are for line of sight installations and

may vary depending on your particular installation.

The antenna connection on the radio modem is an

RPSMA female plug.

B&B Electronics has a wide variety of accessory
antennas. Visit www.bb-elec.com.

Front Panel LED

Status

Power

Red = ON
OFF = No Power

RSSI (Signal Strength)

Green = Strong
Yellow = OK
Red = Weak
OFF = No Signal

Wireless Data

Green = Blink ON with
data

Model #

Indoor
Range

Outdoor
Range

ZP24D-192RM-MR

up to 600
feet

up to 3 miles

ZP24D-96RM-MR

up to 600
feet

up to 3 miles

ZP9D-192RM-MR

up to 1500
feet

up to 7 miles

ZP9D-96RM-MR

up to 1500
feet

up to 7 miles

Summary of Contents for Zlinx ZP Series


















































Search results

Summary of Contents for Zlinx ZP Series

Reviews:

Related manuals for Zlinx ZP Series

Brands by name

Popular brands

B&B Electronics Zlinx ZP Series, Manual

Search results

Summary of Contents for Zlinx ZP Series

Reviews:

Related manuals for Zlinx ZP Series

Brands by name

Popular brands