background image

Installation and Operations Manual 

— Model 730 Series 

INTRODUCTION 

B&B ARMR

                                                                                                                  

A Division of B&B Roadway and Security Solutions        

                                                                                            

0730-9001 Revision C2 

 

 

 SYMBOL MEANING: 

 

 

The lightning flash with arrowhead symbol, within an 
equilateral triangle, is intended to alert the user to the 
presence of non-insulated "dangerous voltage" within the 
product's enclosure that may be of sufficient magnitude to 
constitute a risk of electric shock to persons. 

 

 

The exclamation point within an equilateral triangle is 
intended to alert the user to the presence of important 
operating and maintenance (servicing) instruction in the 
literature accompanying the product. 

 
B&B ARMR does not assume responsibility for injury to persons or property during 
installation, operation, or maintenance.  As the user, you are responsible for correct and 
safe installation, operation, and maintenance of this equipment. Users must follow the 
specific instructions and safety precautions located in this manual. In addition they must: 
Follow the safety standards of the Occupational Safety and Health Administration 
(OSHA), as well as other applicable federal, state, and local safety regulations and 
industry standards and procedures. For installation outside the United States, users must 
also follow applicable international, regional, and local safety standards. 
Engage only trained and experienced staff to install, operate, and maintain the equipment. 
Ensure that all repairs are performed correctly, using properly trained technicians and the 
correct tools and equipment. 

 

This steel barrier is heavy and may drop suddenly if installed 
improperly.  EXTREME care should be given to ensure a safe 
installation barrier is completed. 

Additional system safety devices may be included with this barrier system: 

o

 

Vehicle loop detector(s) – Safety loop 

o

 

Traffic arms  

o

 

Traffic lights  

How to Contact Us 

If you have any questions or experience any problems with your vehicle barrier—or if we 
can help you with any other facility security issues—please contact us directly at:

  

Corporate/Tech Support:      

  

B&B ARMR   

 

 

5900 S. Lake Forest Drive, Suite 230  
McKinney, TX 75070  USA   

 

Telephone: 

(972) 385-7899 

Toll Free:        (800) 367-0387 
Fax:    

(972) 385-9887 

E-mail

[email protected]

 

[email protected]

 

Summary of Contents for 730 Series














Reviews: