Bally ProSlot 6000, Setup And Operation

Page: 39 / 444

©2004 Bally Gaming and Systems
2-39
ProSlot
®
6000
| - Revised, || - New
An accepted coin will cause 09 , Coin Credit, to appear
in the first two digits of the
CREDIT
display. A count
of accepted coins display in the right two digits of
CREDIT
.
A malfunction or improper coin travel will display as
0A , Coin Error Signal, in
CREDIT
as indicated in the
following table:
Input Ports
Port Bit Input Description
0 0 Hold 1 Switch
0 1 Hold 2 Switch
0 2 Hold 3 Switch
0 3 Hold 4 Switch
0 4 Hold 5 Switch
0 5 Hopper Low (Probe) Switch
0 6 Coin Out Switch
0 7 Meter Detection
0 8 Belly Door Switch
0 9 Coin Credit Signal
0 A Coin Error Signal
0 B Change Switch
0 C Spin Switch
0 D Bet One Switch
0 E Bet Max Switch
0 F Cash/Credit Switch
1 0 Bill Door Switch
1 1 Drop Door Switch
1 2 Key Switch
1 3 Hopper Full (Probe) Signal
1 4 Bill Acceptor Busy Signal
1 5 Handle Signal
1 6 Stacker Switch
1 7 Tournament Switch
1 8 Bill Hopper Bill Out Signal
1 9 Bill Hopper Diverter Signal
1 A Bill Hopper Present Switch
1 B Bill Hopper Mid Signal
1 C Bill Hopper Cassette In Switch
1 D Bonus Trigger
1 E Bill Hopper Rear Signal
1 F Reserved
2 3 "Knockoff" Switch
2 4 Coin Mech Switch
2 6 Slant Door
2 9 Pseudo Coin Button
2 B Drop/Diverter Optic
Coin Acceptor Test
#3 - Input Test
Diagnostic Tests and Functions
#4 - Hopper/Printer Test
To enter the Hopper/Printer Test, press and release
the
TEST
button until 04 d appears in
WIN PAID
, indicating
the Hopper/Printer Test is selected. The Message
Center display alternates between Coin and CouP.
Press
SPIN
when the device appears.
Coin—The hopper attempts to pay out 10 coins.
As each coin is dispensed from the hopper,
CREDIT
increments from 0 to 10. Pressing the
CHANGE
button
repeats the test. If an error occurs, the error code
appears in the first two positions of the
CREDIT
display.
Refer to the Malfunction and Game Codes table (page
2-39) for error descriptions. If the machine has a
second hopper, press the
SPIN
button at the start to
select the second hopper.
CouP—The printer will dispense a voided coupon or
voucher.
#5 - Reel Function Test
The Reel Function Test verifies the reels are operating
correctly. When started, the reels spin and stop at
consecutive reel positions in reverse order (21-0).
The spin-stop sequence continues until the test is
exited.
To start the test, press and release the
TEST
button until
05 d appears in
WIN PAID
, indicating the Reel Function
Test is selected.
The reels index to the "0" position, then spin and stop
at the highest number reel position. The
CREDIT
display
shows the number of times the spin-stop sequence
occurred. After a brief pause the reels spin and stop
at the next lower position.
If a reel malfunctions during the spin cycle, the reel
number appears in the third position of
WIN PAID
. The
total number of reel malfunctions appears in the
CREDIT
display. When the reels spin again, the
CREDIT
display
returns to show the number of correct reel spins.
CREDIT shows
the number of reel
malfunctions for all
reels
WIN PAID CREDIT COIN IN
0 5 3 d 4
25¢
The third digit of WIN
PAID shows which
reel malfunctioned.
Example, reel 3.
Note: Holding
CHANGE
when entering
Test #5 initiates a reel calibration and
store the reel-stop center position in
SafeRAM™.